ISO35MDW Digital Isolators от Texas Instruments

Specifies the time interval between an input transition and the corresponding output transition. Critical for timing analysis in digital circuits. Verify against datasheet for specific test conditions, supply voltage, and load capacitance.

Specifies the Boolean operation performed by the logic IC, such as AND, OR, NAND, or XOR. Engineers compare this to match the required signal processing in their circuit. Verify the exact function against the datasheet to ensure correct logic behavior.

Specifies the electrical channel configuration, such as unidirectional or bidirectional, for signal or power routing. This attribute is critical for selecting components like multiplexers, isolators, or level shifters. Verify the channel type against your application requirements and the datasheet to ensure correct signal flow and compatibility.

Specifies the highest voltage that can be applied between the positive and negative supply rails of a dual-supply device. Exceeding this limit may damage the component. Verify this parameter against the datasheet for proper power supply design and reliability.

Check if the component needs both positive and negative supply rails. This affects power design and compatibility with your system. Verify the required voltages and tolerances in the datasheet before selecting the part.

Specifies the logical or operational function of the component, such as switching, amplification, or regulation. This attribute helps identify the device's role in a circuit. Verify the function against the datasheet to ensure it matches your application requirements.

Specifies the lowest DC voltage at which the device reliably operates. Compare this with your supply rail and tolerances to ensure proper startup and functionality. Always verify against the datasheet's operating conditions.

Specifies the highest continuous forward current a diode or LED can safely conduct without overheating or degrading. Compare this limit with your circuit's operating current to ensure reliable performance. Always verify against the datasheet's absolute maximum ratings for your specific device.

Specifies the technique used to drive the output stage, such as PWM, linear, or relay control. This affects efficiency, noise, and response time. Verify the driving mode against your application requirements and the datasheet to ensure compatibility with your load and control signal.

Specifies the longest time for a signal to travel from input to output. Critical for timing analysis in digital circuits. Compare with datasheet values to ensure your design meets speed requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Communication mode of the component: simplex allows one-way transmission, duplex allows two-way. This affects data flow and system design. Choose based on your application's need for bidirectional communication and verify with the datasheet.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Maximum power the component can safely dissipate as heat without damage. Exceeding this may cause failure. Check datasheet for thermal resistance and derating curves under your operating conditions.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Indicates if the output is differential, meaning it provides two complementary signals. This is important for noise immunity and long-distance transmission. Engineers select differential outputs for high-speed or precision applications and verify the output type in the datasheet.

Describes the electrical parameters of the input pins, including voltage thresholds, current levels, and impedance. These characteristics determine how the device interfaces with other circuitry. Check these values against your driving signals to ensure proper logic levels and compatibility.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Minimum common mode transient immunity rating for optocouplers and isolated amplifiers. Indicates the device's ability to withstand rapid voltage changes between input and output without false triggering. Verify against datasheet for reliable operation in noisy industrial environments.

Number of input channels available on each side of the device. Useful for multi-channel isolators, drivers, or logic converters. Confirm channel count and configuration in the datasheet to match application requirements.

Specifies the number of bits the driver can handle, indicating the width of the data path or the number of channels. This determines the maximum data throughput and the number of outputs. Ensure it matches your system's bus width or channel requirements.

Indicates whether the component provides galvanic isolation for its power supply, preventing DC or noise from passing between circuits. Essential for safety and noise immunity in industrial, medical, and automotive applications. Check datasheet for isolation voltage rating.

Specifies the maximum voltage that can be applied between isolated circuits without breakdown. Critical for safety in power supplies, optocouplers, and isolated converters. Verify against datasheet for compliance with required insulation ratings.

Specifies the data width in bits that the receiver can process per transaction. Compare this value with the transmitter and bus architecture to ensure proper data alignment. Verify against the datasheet for supported modes and maximum throughput.

Indicates how many independent transceiver channels are integrated in the component. Each channel can both transmit and receive data. Ensure the count matches your communication interface requirements, such as RS-232 or RS-485, and verify the data rate and protocol compatibility.

The amount of current the device draws from its power supply during normal operation. This is essential for power budget calculations, thermal management, and selecting appropriate power sources. Check datasheet for typical and maximum values under specified conditions.

Nominal voltage for the first power supply input. Compare this value with your system's power rail to ensure compatibility. Verify against the datasheet's recommended operating conditions to avoid overvoltage or undervoltage issues.

Specifies the communication protocol supported by the component, such as UART, SPI, I2C, or CAN. Engineers compare this to ensure compatibility with the system bus and peripherals. Always verify the exact standard and version in the datasheet before design-in.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Overall length of the cable assembly from end to end, including connectors if present. This is critical for routing and installation in your system. Ensure the length matches your application requirements to avoid excess slack or tension that could damage the cable or connections.

Compare the output current relative to the input current in optocouplers and current sensors. This ratio indicates signal transfer efficiency and isolation performance. Verify it against the datasheet for your operating point, as it varies with temperature and forward current.

Specifies the maximum power the component can safely dissipate under defined operating conditions. Compare this value with your circuit's power requirements to prevent overheating and ensure reliable operation. Always verify against the datasheet for derating curves and ambient temperature limits.

Stroke indicates the maximum linear travel distance of a moving part, such as a solenoid plunger or actuator shaft. Engineers compare stroke to ensure the component can achieve the required mechanical displacement in their application. Verify the stroke specification against the datasheet to confirm it meets your system's travel requirements.

Specifies the maximum continuous current available at the first output of a power supply or converter. Compare this value with your load requirements to ensure sufficient headroom. Verify against the datasheet's derating curves and operating conditions.

Specifies the maximum power the component can deliver to the load under rated conditions. Compare this value with your application's power requirement to ensure sufficient headroom. Verify against the datasheet's derating curves and thermal limits for reliable operation.

Indicates the certification body that has tested and approved the component for safety or regulatory compliance. Buyers should verify this matches their target market requirements, and engineers should check the datasheet for the specific standards and marks.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Specifies the highest ambient temperature at which the component can operate reliably. Check this limit against your application's thermal environment to prevent overheating and ensure long-term stability. Always verify with the datasheet for derating curves.

The manufacturer's specific code for the package type, such as SOIC-8 or 0603. Use this to confirm the physical dimensions, pinout, and footprint compatibility with your PCB design. Cross-reference with the datasheet for exact mechanical drawings.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Specifies how many independent output channels the component provides. Compare this when selecting power supplies, drivers, or modules to ensure the device can drive all required loads. Always verify against the datasheet for exact output configuration.

Number of line drivers and receivers integrated in the device, often relevant for RS-232, RS-485, or CAN transceivers. This indicates how many differential or single-ended channels are available. Verify this count matches your bus topology and required node connections.

Indicates the highest power the component can safely dissipate as heat without exceeding its thermal limits. Compare this value with your circuit's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves for elevated ambient temperatures.

Indicates the physical form factor of the component, such as through-hole, surface mount, or chassis mount. Buyers compare this to ensure the part fits the PCB layout and mechanical enclosure. Verify the exact shape against the datasheet before design-in.

This attribute indicates whether the printed circuit board design has been modified from the original version. Buyers should verify this when evaluating product revisions or compatibility with existing designs. Always check the latest datasheet or PCN for details.

Defines the physical mounting method for the component, such as surface mount, through-hole, or chassis mount. This determines PCB layout, assembly process, and mechanical stability. Buyers must match mounting type to their manufacturing capabilities and application environment. Check the datasheet for recommended footprint and soldering profile.

Harmonized Tariff Schedule code used for customs classification and duty calculation when importing or exporting electronic components. Accurate HTS codes are essential for compliance and cost estimation. Buyers and logistics teams must verify the correct code for the specific component to avoid delays or penalties.

Indicates whether the concentration of Substances of Very High Concern in the component exceeds the regulatory threshold set by REACH. This is a critical compliance flag for EU market access. Buyers must verify this status to ensure legal compliance and avoid supply chain disruptions. Check the latest REACH updates for threshold changes.