FMA7AT148 Transistors - Bipolar (BJT) - Arrays, Pre-Biased от Rohm Semiconductor

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Indicates how many independent functional sections are integrated into a single component package. This matters when comparing multi-channel devices or resistor networks. Always verify the exact element count against the datasheet to ensure it matches your circuit design requirements.

Maximum voltage the component can withstand before breakdown occurs. Essential for ensuring safe operation in high-voltage circuits. Verify this rating against your circuit's worst-case voltage spikes to prevent failure and ensure long-term reliability.

Specifies the internal circuit topology or arrangement of the component, such as single, dual, or bridge configuration. This attribute helps engineers select the right part for their circuit design. Always verify the exact configuration against the datasheet to ensure compatibility with your application.

Specifies the semiconductor technology used in the transistor, such as BJT, MOSFET, or IGBT. This determines the device's switching characteristics, drive requirements, and application suitability. Verify the exact type against the datasheet to ensure compatibility with your circuit design.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Specifies the intended circuit role, such as switching, amplification, or RF. Engineers compare this to ensure the transistor's characteristics match the design's requirements. Verify against the datasheet's application section before selecting.

Specifies the semiconductor material used in the transistor's active region. This affects electrical characteristics such as switching speed and voltage rating. Verify the material against the datasheet when selecting for high-frequency or high-power applications.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Maximum power the component can safely dissipate as heat without damage. Exceeding this may cause failure. Check datasheet for thermal resistance and derating curves under your operating conditions.

Maximum power the component can safely dissipate as heat without exceeding its thermal limits. Compare this rating with your application's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves and ambient temperature conditions.

Specifies the highest continuous current the device can supply at its output without exceeding thermal or electrical limits. Compare this value with your load requirements and derating curves. Always verify against the datasheet for your operating conditions.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies whether the component or signal has a defined positive and negative orientation, such as for diodes, electrolytic capacitors, or connectors. Incorrect polarity can cause failure or unsafe operation. Always check the datasheet and board markings before installation.

Specifies the maximum voltage that can be applied between collector and emitter without causing breakdown. Critical for power transistors and switching circuits. Verify against datasheet to ensure safe operating margin under worst-case conditions.

Minimum DC current gain (hFE) of a bipolar transistor at a specified collector current and voltage. This value indicates the lowest amplification the device guarantees. Engineers compare it to ensure sufficient drive for the load. Always verify against the datasheet for your operating conditions.

Specifies the maximum DC voltage the component can safely handle under rated conditions. Engineers compare this to the circuit's operating voltage to ensure adequate margin. Always verify against the datasheet's derating curves for temperature and reliability.

Minimum DC current gain measured at a specified collector current and collector-emitter voltage. This parameter indicates the transistor's amplification capability. Compare it with your circuit requirements and verify the test conditions in the datasheet.

Maximum allowable voltage between collector and emitter with the base terminal open. Exceeding this rating can cause breakdown or permanent damage. Verify against the datasheet for safe operating conditions in your circuit design.

This is the maximum collector-emitter voltage drop when the transistor is fully on at the given base and collector currents. Lower values mean less power loss. Check the datasheet to confirm it meets your circuit's switching and efficiency requirements.

Transition frequency is the frequency at which the transistor's current gain falls to unity. It indicates the upper limit for useful amplification. Engineers compare this value to ensure the device meets bandwidth requirements for RF and high-speed switching applications. Always verify against the datasheet.

Maximum continuous collector current that the transistor can handle without damage. Compare this rating with your circuit's peak current demand. Always verify against the datasheet for thermal limits and derating conditions.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Maximum collector current when the transistor is in cutoff. Indicates leakage and off-state performance. Important for low-power and high-impedance circuits. Check datasheet to ensure it meets your application's leakage requirements.

Specifies the transition frequency (fT) of a transistor, where current gain drops to unity. This parameter indicates high-frequency performance and is critical for RF amplifiers, oscillators, and high-speed switching circuits. Compare fT values to ensure adequate bandwidth for your application.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the resistance value between the emitter and base terminals in a digital transistor or bias resistor network. This resistor helps ensure stable off-state and faster switching. Compare R2 values when selecting transistors for logic-level interfacing or to match input impedance requirements.

Specifies the maximum steady DC current the transistor's collector can carry without exceeding thermal limits. Compare this value with your circuit's peak current demand to ensure reliable operation. Always verify against the datasheet's safe operating area and derating curves for your operating temperature.

Specifies the maximum continuous current the component can safely carry under specified conditions. Compare this value with your circuit's expected load to ensure reliable operation. Always verify against the datasheet for temperature derating and mounting considerations.

Maximum collector-emitter saturation voltage for a bipolar transistor. This parameter indicates the voltage drop when the transistor is fully on. Compare it with your circuit's supply voltage and ensure it meets your design's power loss and thermal requirements. Always verify against the datasheet's test conditions.

Specifies the resistance value connected in series with the base terminal of a digital transistor. This resistor sets the base current and influences saturation voltage and switching speed. Compare R1 values to ensure proper drive levels for your input voltage.

Lists any extra characteristics or capabilities beyond the standard specifications, such as built-in protection, special mounting options, or enhanced performance. Review these features to ensure they meet your application's specific needs and compare them across similar parts.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.