ADSP-2181KS-160 Embedded - DSP (Digital Signal Processors) от Analog Devices Inc

Maximum vertical dimension from the seating plane to the top of the component body. Critical for PCB clearance and enclosure fit. Verify against the datasheet when designing mechanical constraints or checking compatibility with mating parts.

Specifies the number of parallel data lines in bits for microcontrollers, DSPs, or memory interfaces. Wider buses enable higher throughput but affect pin count and power. Verify against the datasheet to ensure compatibility with your system's architecture and required performance.

Specifies the functional category of the integrated circuit, such as microprocessor, microcontroller, or peripheral controller. This classification helps engineers quickly identify the device's role in a system. Verify the exact type against the datasheet to ensure compatibility with your application's processing and interface requirements.

Shows whether the component includes an integrated cache memory to speed up data access for the processor. Compare cache presence and size to assess performance for real-time or high-throughput tasks. Verify details in the datasheet.

Specifies the required power supply voltages for the component. Engineers use this to ensure the board's power rails match the device's needs. Verify against the datasheet's recommended operating conditions to avoid undervoltage or overvoltage issues.

Specifies the maximum duration a component can withstand at the peak reflow temperature during soldering. Critical for evaluating solder joint reliability and preventing thermal damage. Verify against the datasheet's recommended soldering profile to ensure proper assembly.

Specifies the number of bits in a single data word for digital components. This determines the maximum data width the device can process or store. Compare bit sizes when selecting microcontrollers, ADCs, DACs, or memory chips to ensure compatibility with your system's data bus and processing requirements.

Indicates how many serial input/output interfaces the component provides. Compare this when selecting microcontrollers, FPGAs, or interface ICs to ensure enough UART, SPI, or I2C channels for your design. Verify against the datasheet pinout and peripheral list.

Indicates how many direct memory access channels the microcontroller or processor provides. More channels allow simultaneous data transfers without CPU intervention. Compare with your system's peripheral and memory transfer requirements to ensure sufficient bandwidth.

Indicates whether the device supports JTAG boundary scan for testing interconnections and internal logic. Useful for board-level testing and debugging. Confirm the boundary scan description in the datasheet to ensure compatibility with your test tools and chain configuration.

Specifies how many independent I2C bus interfaces the component provides. Compare this when selecting a device for multi-peripheral systems. Verify against the datasheet to ensure sufficient channels for your design.

Specifies the absolute maximum supply voltage that can be applied to the device without causing damage or malfunction. Engineers must verify this limit against the datasheet to ensure safe operating conditions and avoid overvoltage stress in the application.

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Number of independent UART interfaces for serial communication. Each channel supports bidirectional data transfer with configurable baud rate. Ensure the count meets your connectivity needs for peripherals, debugging, or inter-processor links. Verify pin availability in the datasheet.

Indicates the count of independent timer modules integrated into the microcontroller or IC. Compare this when selecting devices for time-critical tasks like PWM generation, event counting, or real-time scheduling. Verify the exact timer features and resolution in the datasheet.

Total storage capacity of the memory chip, typically expressed in bits or bytes. Compare densities to match your application's code and data requirements. Verify against the datasheet to ensure sufficient headroom for firmware and runtime variables.

Amount of volatile memory available for runtime data and stack. Larger RAM enables more complex applications and buffering. Compare with your software's memory footprint and verify against the datasheet to avoid overflow and ensure reliable operation.

Input capacitance is the effective capacitance seen at the input terminal of a component. It affects signal integrity, impedance matching, and switching behavior. Engineers compare this value to ensure proper circuit operation and to avoid unintended resonance or filtering. Verify against the datasheet for accurate modeling.

Specifies the amount of random access memory available for data storage during operation. This determines the complexity of tasks the component can handle. Buyers should verify that the RAM size meets the application's memory requirements, especially for real-time processing or buffering.

Maximum operating frequency specifies the highest clock or switching rate at which the component reliably functions. Designers verify this limit against their application's timing budget to avoid signal integrity issues and ensure stable operation over temperature and voltage variations.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Terminal pitch is the center-to-center distance between adjacent leads or pads on a component. It determines PCB layout compatibility and soldering feasibility. Verify against the datasheet to ensure your footprint matches the component's actual lead spacing.

Indicates the component's compliance status with the EU REACH regulation. Buyers should verify this code against the manufacturer's declaration to ensure restricted substances are within allowable limits for their target market.

Shows if the component meets a specific industry standard or reliability level. Buyers should verify this against the datasheet to ensure the part is suitable for their application's environmental and performance requirements.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Specifies the lowest DC input voltage at which the component reliably operates. Compare this value with your system's power rail tolerances and the device's recommended operating conditions to ensure stable performance across all load and temperature ranges.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Harmonized Tariff Schedule code used for customs classification of electronic components. Helps determine duties and regulatory requirements. Buyers should confirm the code with a customs broker for accurate shipping.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Specifies the bit width of the on-chip program ROM in microcontrollers and SoCs. Wider ROM allows larger firmware and more complex instructions. Verify against the datasheet to ensure compatibility with your code size and memory architecture.

Operating frequency of the component, typically the clock or switching frequency. This determines the speed of operation and affects power dissipation and signal integrity. Verify the frequency range against your application's requirements and the datasheet specifications.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Specifies how many analog input signals the ADC can sample and convert to digital. Compare this when selecting microcontrollers or data acquisition ICs. Verify against the datasheet to ensure enough channels for your application.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Defines the operating temperature range classification for the component, such as commercial, industrial, or automotive. This indicates the environmental conditions the device can withstand. Ensure the grade matches your application's ambient temperature requirements.

Specifies the number of address lines used to access memory or registers. Wider buses address more locations, affecting maximum memory capacity. Verify against the datasheet for compatibility with your microcontroller or processor design.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.