PSK-15W-9-T DC DC Converters от CUI

Maximum continuous power dissipation or output power the component can handle under specified conditions. Compare this rating with your application's power requirements to ensure reliable operation. Always verify against the datasheet for thermal limits and derating.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies the electrical form of the output signal, such as digital, analog, or open collector. This determines how the component interfaces with your circuit. Verify the output type against your system requirements and the datasheet to ensure proper signal compatibility and avoid logic level mismatches.

Specify the typical end-use scenarios for this electronic component, such as consumer electronics, automotive, industrial, or telecommunications. This helps engineers quickly assess suitability for their design. Verify against the datasheet's application section.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Efficiency indicates how effectively a power component converts input power into useful output power, expressed as a percentage. Higher efficiency means less energy lost as heat, which is critical for thermal management and system reliability. Always verify the efficiency curve in the datasheet under your operating conditions.

Specifies how many independent output channels the component provides. Compare this when selecting power supplies, drivers, or modules to ensure the device can drive all required loads. Always verify against the datasheet for exact output configuration.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Lifecycle status of the product, such as active, obsolete, or end-of-life. This affects long-term availability and design reliability. For production, choose active products to ensure supply continuity. Check the datasheet or manufacturer for lifecycle details.

Specifies the nominal or regulated output voltage provided on the first output channel of a multi-channel power supply or DC-DC converter. Verify this value against the datasheet to ensure it meets your circuit's requirements, especially for precision or load-sensitive applications.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Indicates the certification body that has tested and approved the component for safety or regulatory compliance. Buyers should verify this matches their target market requirements, and engineers should check the datasheet for the specific standards and marks.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the AC components superimposed on the DC output of a power supply or converter. Lower values mean cleaner power for sensitive loads. Verify against datasheet specifications under full load and specified bandwidth.

Maximum continuous power the device can deliver at its output under specified conditions. Essential for matching power supplies to load requirements. Always confirm derating curves and ambient temperature limits in the datasheet.

Select the physical style or form factor of the component, such as through-hole, surface mount, or chassis mount. This affects PCB layout, assembly process, and mechanical fit. Verify the exact package style against the datasheet to ensure compatibility with your design and manufacturing requirements.

Specifies the highest DC voltage that can be safely applied to the input terminals without causing damage or malfunction. Verify this rating against your power supply design and ensure it exceeds the maximum expected input voltage to prevent overvoltage stress.

Describes the electrical configuration of the input and output connections, such as single-ended, differential, push-pull, or open-collector. This determines how the component interfaces with your circuit and affects signal integrity and compatibility with other devices.

Allowed deviation from the nominal value, expressed as a percentage. Determines precision of resistors, capacitors, and inductors. Choose tighter tolerance for precision circuits, but verify actual performance in the datasheet.

This attribute indicates whether the printed circuit board design has been modified from the original version. Buyers should verify this when evaluating product revisions or compatibility with existing designs. Always check the latest datasheet or PCN for details.

Indicates whether the component is certified or designed for use in medical devices, meeting specific safety and reliability standards. This is critical for applications requiring patient safety, such as diagnostic equipment or monitoring systems, and must be verified against the datasheet.

Specifies the highest ambient temperature at which the component can operate reliably. Exceeding this limit may cause performance degradation or permanent damage. Always verify this value against the datasheet for your specific application and thermal conditions.

Specifies the lowest isolation voltage rating between input and output, ensuring electrical separation and safety. This is essential for applications requiring galvanic isolation to protect against high voltages or noise. Always confirm this rating meets your system's isolation requirements.

Reference number of the applicable industry standard that the component complies with, such as IEC, UL, or MIL specifications. This helps engineers verify regulatory compliance and ensure the part meets required safety and performance criteria for their application.

Select the component category that best matches your application, such as resistor, capacitor, diode, or connector. This classification helps narrow down the correct part family and ensures compatibility with your circuit design. Verify the type against the datasheet to avoid mismatches.

Maximum input current is the highest current the device can draw under specified conditions. It is critical for sizing input power supplies, fuses, and PCB traces. Always verify this value against the datasheet to ensure safe operation and avoid overloading the input circuit.

Input frequency specifies the frequency range of the AC input power that the device is designed to accept. It is essential for ensuring compatibility with regional power grids or specific AC sources. Check the datasheet to confirm the device operates correctly within your required frequency range.

Specifies the maximum voltage that can be applied between isolated circuits without breakdown. Critical for safety in power supplies, optocouplers, and isolated converters. Verify against datasheet for compliance with required insulation ratings.

Package height is the physical height of the component package, measured from the mounting surface to the top. It is crucial for mechanical design, ensuring clearance in enclosures and proper fit on PCBs. Always verify this dimension against the datasheet to avoid assembly issues.

Power indicator describes the type of visual indicator used to show power status, such as an LED or lamp. It helps engineers and buyers understand how the device signals its operational state. Verify the indicator type and its electrical characteristics in the datasheet for proper integration.

Physical width of the component package, measured in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure the component fits the designated footprint and does not interfere with adjacent parts.

Highest alternating current voltage that can be safely applied to the input terminals without causing damage or malfunction. This limit is essential for power supplies and AC-DC converters. Always check the datasheet to ensure your application's AC line voltage stays within this absolute maximum rating.

Input voltage rating or range for which the component is designed to operate. Exceeding this can damage the device. Check the datasheet for absolute maximum ratings and recommended operating conditions to ensure your supply voltage is within safe limits.

Measures how much the output voltage changes when the input voltage varies. Lower values indicate better stability. Critical for power supplies and regulators. Check datasheet for specified input range and load conditions.

Physical dimensions of the component, typically length, width, and height. These measurements are critical for PCB layout and mechanical fit. Always verify against the datasheet for exact tolerances and mounting requirements.

Style of connector used on the output side of the component, such as terminal block, USB, or coaxial. This determines mating cables and system integration. Confirm compatibility with your wiring and enclosure design before ordering to avoid mechanical mismatches.

Indicates whether the component can be customized or programmed for specific application requirements. Buyers should check this attribute to determine if the part supports configuration options such as adjustable parameters, firmware, or hardware settings. Verify with the datasheet or configuration guide before ordering.

Physical length of the component package, measured in millimeters. This dimension is essential for PCB layout and mechanical fit. Verify against the datasheet to ensure the component fits the designated footprint and does not interfere with adjacent parts.

Color of the power supply enclosure or housing. This attribute is primarily aesthetic but may be relevant for product branding, visual identification, or matching system enclosures. Confirm with the manufacturer if color consistency is important for your application.

Specifies the lowest ambient temperature at which the component reliably functions. Critical for automotive, industrial, and outdoor applications. Verify against datasheet to ensure performance and longevity in your operating environment.

The weight of the component in grams, useful for logistics, mechanical design, and weight-sensitive applications. Compare weights when evaluating similar parts for assembly or shipping cost calculations. Verify the value in the datasheet if precise weight is critical for your design.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates how much the output voltage changes when the load current varies. Better load regulation means a more stable output. Check the datasheet for the specified load range and conditions to ensure your application's voltage tolerance is met.

Lowest direct current voltage required for the component to operate correctly. This is a key specification for DC-DC converters and power management ICs. Ensure your input supply stays above this threshold to maintain regulation and avoid dropout or shutdown.

Style of connector used on the input side of the component, such as terminal block, USB, or coaxial. This determines mating cables and system integration. Confirm compatibility with your wiring and enclosure design before ordering to avoid mechanical mismatches.

Lowest alternating current voltage required for the component to operate correctly. This is essential for power supplies and AC-DC converters to ensure they start and regulate under low line conditions. Verify this rating against your expected AC mains variations.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Specifies the maximum continuous current available at the first output of a power supply or converter. Compare this value with your load requirements to ensure sufficient headroom. Verify against the datasheet's derating curves and operating conditions.

Amount of current the component can supply at its output under specified conditions. This rating is crucial for power supplies, regulators, and converters to ensure they can drive the load. Verify the maximum continuous current and consider derating for temperature and reliability.

Voltage provided at the output of the component under specified load and input conditions. This is a critical parameter for power supplies, regulators, and converters. Verify the nominal output voltage and its tolerance to ensure it matches your load requirements.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Efficiency is the ratio of output power to input power, expressed as a percentage. It indicates how effectively a power conversion device uses input energy. Compare values when selecting power supplies, converters, or amplifiers, and verify against the datasheet for specific operating conditions.

The US Export Control Classification Number determines export licensing requirements for electronic components. Verify the current ECCN from the manufacturer or datasheet, as it affects international shipping and compliance with US regulations.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Defines the physical mounting method for the component, such as surface mount, through-hole, or chassis mount. This determines PCB layout, assembly process, and mechanical stability. Buyers must match mounting type to their manufacturing capabilities and application environment. Check the datasheet for recommended footprint and soldering profile.