CNY17-3 TVS - Diodes от Vishay

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Time required for a signal to transition from a low to a high level, typically measured between 10% and 90% of the amplitude. Important for digital interfaces, switching regulators, and pulse circuits. Check the datasheet for test conditions and load capacitance.

Specifies how many independent signal paths or outputs the component provides. Compare this value with your circuit requirements to ensure each channel can be used separately. Verify the channel configuration in the datasheet, as some devices may share pins or have internal connections.

Indicates how many independent functional sections are integrated into a single component package. This matters when comparing multi-channel devices or resistor networks. Always verify the exact element count against the datasheet to ensure it matches your circuit design requirements.

Voltage at which the diode begins to conduct in reverse bias, leading to breakdown. Critical for selecting diodes in rectifier and protection circuits. Ensure this voltage exceeds your maximum reverse voltage with margin. Check datasheet for tolerance and temperature effects.

Specifies the configuration of the input signal path, such as single-ended or differential. This affects noise immunity and interface compatibility. Verify the input type against your signal source and the datasheet to ensure proper connection and performance.

Specifies the maximum continuous current each output channel can deliver. Compare this with your load requirements and derating curves. Verify against the datasheet for thermal limits and safe operating area.

Time from when the input signal crosses its threshold until the output begins to turn on. This parameter affects switching speed and power dissipation in high-frequency circuits. Verify it against the datasheet for your specific load and drive conditions.

Specifies the maximum continuous forward current the component can handle without damage. Compare this rating with your circuit's operating current to ensure reliable performance. Always verify against the datasheet for derating curves and temperature conditions.

Forward voltage is the voltage drop across a diode or LED when it conducts current in the forward direction. It affects power dissipation and efficiency. Compare this value with your circuit's supply voltage and check the datasheet for the specified test current.

Maximum continuous direct current that can flow through the device in the forward direction without damage. Critical for LEDs, diodes, and optocouplers to prevent overheating and ensure reliable operation. Always check the datasheet for derating curves and ambient temperature limits.

Measures the time from when the turn-off command is applied to when the device actually begins to switch off. This delay affects switching losses and timing in power circuits. Engineers compare this parameter to ensure proper synchronization and to minimize power dissipation during high-frequency operation.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Maximum power the component can safely dissipate as heat without exceeding its thermal limits. Compare this rating with your application's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves and ambient temperature conditions.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Specifies the maximum current each output channel can source or sink continuously. Compare this value with your load requirements to ensure the driver or amplifier can handle the current without overheating or damage. Always verify against the datasheet for absolute maximum ratings and derating curves.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Maximum power the component can safely dissipate as heat without damage. Exceeding this may cause failure. Check datasheet for thermal resistance and derating curves under your operating conditions.

Specifies the maximum voltage that can be applied between isolated circuits without breakdown. Critical for safety in power supplies, optocouplers, and isolated converters. Verify against datasheet for compliance with required insulation ratings.

Indicates the certification body that has tested and approved the component for safety or regulatory compliance. Buyers should verify this matches their target market requirements, and engineers should check the datasheet for the specific standards and marks.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Maximum continuous collector current that the transistor can handle without damage. Compare this rating with your circuit's peak current demand. Always verify against the datasheet for thermal limits and derating conditions.

Specifies the maximum DC voltage the component can safely handle under rated conditions. Engineers compare this to the circuit's operating voltage to ensure adequate margin. Always verify against the datasheet's derating curves for temperature and reliability.

Voltage drop across collector-emitter when the device is fully on. Determines conduction losses and efficiency. Lower saturation voltage means less power dissipation. Verify against datasheet for collector current and temperature.

Specifies the maximum voltage that can be applied between collector and emitter without causing breakdown. Critical for power transistors and switching circuits. Verify against datasheet to ensure safe operating margin under worst-case conditions.

Maximum allowable voltage between collector and emitter with the base terminal open. Exceeding this rating can cause breakdown or permanent damage. Verify against the datasheet for safe operating conditions in your circuit design.

Minimum ratio of output collector current to input LED current for an optocoupler. This parameter indicates the lowest gain you can expect from the device. Verify it against the datasheet to ensure sufficient signal transfer in your circuit design.

Specifies the regulated voltage level available at the output pin under specified load and input conditions. Compare this value with your circuit requirements and verify against the datasheet's tolerance and temperature derating.

Specifies the highest continuous current the input pin can safely handle without damage or performance degradation. Compare this limit with your circuit's expected input current to ensure reliable operation. Always verify against the datasheet's absolute maximum ratings for your specific operating conditions.

Maximum ratio of output collector current to input LED current for an optocoupler. This upper limit helps you avoid saturation or excessive output drive. Always compare with the datasheet to ensure your circuit operates within the intended gain range.

Specifies the electrical form of the output signal, such as digital, analog, or open collector. This determines how the component interfaces with your circuit. Verify the output type against your system requirements and the datasheet to ensure proper signal compatibility and avoid logic level mismatches.

Defines the current drawn at the input terminal under normal operating conditions. Essential for power supply design and thermal management. Check this value against your system's power budget and ensure the input source can deliver it without voltage drop.

Specifies the highest output voltage the component can provide under specified conditions. Compare this value with your circuit requirements to ensure compatibility. Always verify against the datasheet for exact limits and tolerances.

Specifies the highest voltage the device can deliver at its output under specified conditions. Compare this limit with your application's supply and load requirements to ensure safe operation and avoid overvoltage damage.

The maximum collector-emitter voltage drop when the transistor is fully saturated. This parameter indicates power loss and efficiency in switching applications. Lower values are preferred for high-current circuits. Always check this against the datasheet for your operating conditions.

Indicates the physical package type as designated by the component manufacturer, such as SOIC, QFN, or BGA. This affects PCB footprint, thermal performance, and assembly processes. Confirm compatibility with your board layout and soldering requirements before design finalization.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Typical rise and fall time of the output signal, indicating how quickly the device transitions between logic levels. These values affect signal integrity and switching losses. Compare them with your application's required slew rate and check the datasheet for test conditions.

Typical time for the output signal to transition from 90% to 10% of its amplitude. This parameter indicates switching speed and affects high-frequency performance. Compare with rise time and verify against the datasheet for your specific operating conditions.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Typical voltage drop across the device when it conducts in the forward direction. Compare this value to ensure your circuit's power dissipation and efficiency meet design targets. Always verify against the datasheet for your specific operating current and temperature.

Typical time required for the device to switch from off to on and from on to off. This dynamic characteristic affects switching speed and power dissipation. Check the datasheet for test conditions, as actual times may vary with load and drive.