JS28F160C3TD70 Memory от Intel

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Shows if the component meets a specific industry standard or reliability level. Buyers should verify this against the datasheet to ensure the part is suitable for their application's environmental and performance requirements.

Terminal pitch is the center-to-center distance between adjacent leads or pads on a component. It determines PCB layout compatibility and soldering feasibility. Verify against the datasheet to ensure your footprint matches the component's actual lead spacing.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Defines the operating temperature range classification for the component, such as commercial, industrial, or automotive. This indicates the environmental conditions the device can withstand. Ensure the grade matches your application's ambient temperature requirements.

Specifies the internal arrangement of memory cells, typically expressed as words by bits. This affects how data is accessed and stored. Engineers compare this to ensure compatibility with their system's bus width and addressing scheme. Always verify against the datasheet for exact configuration.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Mounting type: surface mount or through-hole. Surface mount components are placed directly on the PCB, saving space and enabling automated assembly. Through-hole components offer stronger mechanical bonds. Verify the mounting style matches your PCB design and assembly process.

Specifies the highest ambient temperature at which the component can operate reliably. Check this limit against your application's thermal environment to prevent overheating and ensure long-term stability. Always verify with the datasheet for derating curves.

Specifies the lowest ambient temperature at which the component remains fully functional. Check this limit against your application's environmental extremes to ensure reliable operation. Exceeding this minimum may cause performance degradation or failure, so always verify with the datasheet.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Indicates the component's compliance status with the EU REACH regulation. Buyers should verify this code against the manufacturer's declaration to ensure restricted substances are within allowable limits for their target market.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Standardized interface for flash memory devices, enabling host controllers to identify and program them. It ensures compatibility across manufacturers. Engineers use this to verify that the memory can be accessed with standard commands. Check the datasheet for supported commands and timing.

Harmonized Tariff Schedule code used for customs classification of electronic components. Helps determine duties and regulatory requirements. Buyers should confirm the code with a customs broker for accurate shipping.

Specifies the memory region reserved for boot code in microcontrollers, flash, or EEPROM devices. This block is protected to ensure reliable startup. Verify its size and protection features against the datasheet when selecting parts for firmware updates or secure boot applications.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Interface for sending commands to a device, typically for configuration or control. It defines the protocol and command set. Engineers compare this to ensure the device can be integrated with their system. Verify the command set and response timing in the datasheet.

Specifies the number of bits transferred simultaneously between the memory device and the controller. Wider buses enable higher data throughput. Verify this parameter against the datasheet to ensure compatibility with your system's bus architecture and expected performance.

Specifies the smallest erasable block size in memory devices. Compare sector sizes when selecting flash or EEPROM for firmware updates or data storage. Verify against the datasheet to ensure compatibility with your file system and wear-leveling requirements.

Maximum current drawn by the component when in standby or sleep mode. Lower values extend battery life in portable designs. Verify against datasheet conditions, as standby current can vary with supply voltage and temperature.

Data polling is a method used in memory devices to verify that a write operation has completed. It involves reading a specific data bit until it matches the expected value. Engineers compare this feature to ensure reliable programming and to avoid premature read operations.

A status bit that toggles state to indicate a change in device condition, such as program completion or error. It is used for polling or interrupt generation. Engineers monitor this bit to track device status. Check the datasheet for its behavior and timing.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Select the component category that best matches your application, such as resistor, capacitor, diode, or connector. This classification helps narrow down the correct part family and ensures compatibility with your circuit design. Verify the type against the datasheet to avoid mismatches.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies the number of sectors and their individual size for rotary switches or encoders. This attribute helps engineers determine the number of positions and the angular spacing between them. Verify against the datasheet to ensure compatibility with your control panel or circuit design.

Specifies the total memory capacity of a device, typically expressed in bits or bytes. This attribute is essential for selecting memory ICs, storage modules, or microcontrollers with embedded memory. Compare density to ensure sufficient storage for your application's code and data.

Maximum height of the component above the mounting surface when installed. Critical for mechanical fit in enclosures or when spacing is tight. Verify this dimension against your PCB clearance and assembly tolerances to avoid interference.

Thickness of the component, a critical dimension for PCB clearance, enclosure fit, and thermal performance. This measurement is especially important for capacitors, inductors, and connectors. Ensure the thickness meets your design constraints and does not interfere with adjacent components. Check the datasheet for tolerance and recommended mounting height.

Lists any extra characteristics or capabilities beyond the standard specifications, such as built-in protection, special mounting options, or enhanced performance. Review these features to ensure they meet your application's specific needs and compare them across similar parts.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Specifies the highest frequency signal that can be applied to the input without causing malfunction or performance degradation. Compare this value with your system's operating frequency to ensure reliable operation. Always verify against the datasheet for your specific part.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

JEDEC standard code that defines the package outline and dimensions. Use it to verify physical compatibility and footprint before PCB design. Compare with the datasheet to ensure the component meets your assembly and manufacturing requirements.

Specifies the highest DC supply voltage the component can tolerate without damage or malfunction. Engineers compare this to the system's power rail to ensure safe operation. Always verify against the datasheet's absolute maximum ratings.

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Specifies the maximum duration a component can withstand at the peak reflow temperature during soldering. Critical for evaluating solder joint reliability and preventing thermal damage. Verify against the datasheet's recommended soldering profile to ensure proper assembly.

Minimum supply voltage for proper operation. Check the datasheet to ensure your power rail meets this threshold. Critical for low-voltage designs and battery-powered applications. Compare across parts to avoid undervoltage failures.

Programming voltage is the specific voltage required to write or erase data in programmable devices like EEPROMs, flash memory, or microcontrollers. It must be applied precisely during programming; incorrect levels can cause write failures or permanent damage, so always follow the datasheet's programming procedure.

Indicates whether the component communicates via parallel or serial interface. This affects wiring complexity, data transfer speed, and compatibility with your microcontroller or system bus. Verify the interface type against your design requirements and the datasheet before integration.

Defines the control method used by a power management IC, such as voltage mode, current mode, or hysteretic. This affects transient response, stability, and external component selection. Ensure the mode matches your application's performance needs.

Maximum frequency the device can generate on its clock output. Important for timing applications and system synchronization. Ensure it meets your design requirements and check jitter specifications in the datasheet.

Specifies the required power supply voltages for the component. Engineers use this to ensure the board's power rails match the device's needs. Verify against the datasheet's recommended operating conditions to avoid undervoltage or overvoltage issues.

Maximum current drawn from the power supply under specified operating conditions. Use this to estimate power dissipation and design your power supply and thermal management. Always check the datasheet for test conditions, as current can vary with voltage, frequency, and load.