MT29F4G08ABADAH4 NAND Flash от Micron Technology

Total storage capacity of the memory chip, typically expressed in bits or bytes. Compare densities to match your application's code and data requirements. Verify against the datasheet to ensure sufficient headroom for firmware and runtime variables.

This field captures any additional notes from the original manufacturer or distributor. Use it to record specific part markings, packaging details, or special handling instructions that are not covered by other attributes. Always verify these notes against the official datasheet before design-in.

Provides additional details about error correction code features, such as supported algorithms, protection scope, or implementation specifics. Use this to understand the device's error handling capabilities and ensure it meets your system's reliability requirements. Always cross-check with the datasheet for exact specifications.

Indicates the number of data bits the memory device can transfer in parallel per access. This affects system bus width matching and overall throughput. Confirm this value against the datasheet to ensure proper interfacing with your microcontroller or processor's data bus.

Specifies the Open NAND Flash Interface version supported by the memory device. This determines the maximum interface speed and feature set. Verify compatibility with your controller and system design to ensure optimal performance and reliability.

Highlights key areas to inspect during quality control, such as solder joints, lead integrity, or marking legibility. Helps procurement teams and inspectors focus on critical parameters to ensure component reliability and compliance with specifications.

Provides compatibility information with other components, such as voltage levels, logic families, or connector types. Essential for avoiding integration issues in complex systems. Always verify compatibility with your specific design and reference designs.

Manufacturer-specific code identifying the physical package style and dimensions. Use this code to cross-reference datasheets and ensure the component fits your PCB layout and assembly process. Verify against the official package drawing before design.

Specifies the physical dimensions of the component package, such as length, width, and height. This attribute helps determine board space requirements and compatibility with assembly processes. Verify against the datasheet for precise measurements.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates the number of program/erase cycles a memory device can withstand before performance degrades. This is critical for flash and EEPROM in applications with frequent writes. Engineers compare endurance to ensure data retention and reliability over the product's lifetime. Verify the specified endurance rating in the datasheet.

Specifies how long stored data remains valid without applied power. This is essential for non-volatile memories in battery-powered or long-life applications. Engineers compare retention to ensure data integrity over the product's expected lifetime. Verify the retention rating under specified temperature conditions in the datasheet.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Unique alphanumeric identifier assigned by the original manufacturer to specify a particular component version. Use this number to cross-reference datasheets, verify exact specifications, and ensure compatibility with your design. Always confirm it matches the part you intend to order.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Specifies the communication protocol or interface type used by the component, such as I2C, SPI, UART, or USB. This determines how the device connects to a microcontroller or system. Verify compatibility with your host controller and bus voltage levels before design-in.

Defines the underlying technology used for data storage, such as SRAM, DRAM, or Flash. Determines volatility, speed, and endurance. Choose based on your application's need for persistence and access speed.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Indicates the maximum voltage the component can withstand or operate at, depending on context. Critical for ensuring the part is not overstressed in your application. Always compare with your circuit's voltage levels and consider transient spikes.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.