NCP1117ST25T3G PMIC - Voltage Regulators - Linear от ON Semiconductor

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Confirms whether the component is manufactured without halogenated compounds, such as bromine or chlorine, which are restricted in many industries due to environmental and safety regulations. Important for compliance with green standards and for use in sensitive applications.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Specifies the packaging format for delivery, such as tube, reel, tray, or tape and reel. This affects handling, storage, and assembly processes. Verify the packing method against your production requirements and the datasheet to ensure compatibility with your pick-and-place equipment.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the electrical form of the output signal, such as digital, analog, or open collector. This determines how the component interfaces with your circuit. Verify the output type against your system requirements and the datasheet to ensure proper signal compatibility and avoid logic level mismatches.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Specifies the stable voltage output used as a benchmark for the component's operation. Compare this value when selecting voltage references or regulators. Always verify against the datasheet for accuracy and temperature stability.

Specifies the maximum allowable deviation from the nominal voltage rating for a component. This parameter is critical for ensuring stable operation in power supply and regulation circuits. Always verify this value against the datasheet to prevent overvoltage conditions that could damage the component or reduce system reliability.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Specifies the highest continuous current the device can supply at its output without exceeding thermal or electrical limits. Compare this value with your load requirements and derating curves. Always verify against the datasheet for your operating conditions.

Specifies how many independent output channels the component provides. Compare this when selecting power supplies, drivers, or modules to ensure the device can drive all required loads. Always verify against the datasheet for exact output configuration.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Specifies the lowest output voltage the component can reliably provide under specified conditions. Compare this value with your circuit's minimum required voltage to ensure proper operation. Always verify against the datasheet's electrical characteristics and test conditions.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Quiescent current is the current drawn by the device when it is in standby or no-load condition. It affects battery life in portable applications. Compare this value across similar components to ensure low power consumption. Always verify against the datasheet for your specific operating conditions.

Terminal pitch is the center-to-center distance between adjacent leads or pads on a component. It determines PCB layout compatibility and soldering feasibility. Verify against the datasheet to ensure your footprint matches the component's actual lead spacing.

Specifies the regulated voltage level available at the output pin under specified load and input conditions. Compare this value with your circuit requirements and verify against the datasheet's tolerance and temperature derating.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Specifies the DC current flowing into the input terminals of an operational amplifier or other analog IC. It affects offset voltage and signal accuracy. Compare values when selecting precision amplifiers, and verify against the datasheet for your operating conditions.

Minimum voltage required at the input for the component to operate correctly. Below this level, the device may not function or may produce incorrect outputs. Verify that your power supply provides at least this voltage under all load conditions.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Maximum dropout voltage is the minimum input-to-output voltage difference required for a regulator to maintain regulation. Lower dropout improves efficiency in battery-powered designs. Verify this parameter against the datasheet for your load current and temperature range.

Specifies the topology of the output stage, such as push-pull, open collector, or half-bridge. This determines how the device drives loads and interfaces with external circuitry. Verify against the datasheet to ensure compatibility with your application's requirements.

Specifies the deviation of the actual output voltage from the nominal value under specified conditions. Compare this parameter when selecting regulators or converters for precision applications. Verify the tolerance and test conditions in the datasheet to ensure your design meets required voltage accuracy.

Nominal dropout voltage for the first output. This is the minimum input-to-output differential required to maintain regulation. Compare with your operating conditions and verify against the datasheet for load and temperature variations.

Built-in safeguards that prevent damage from overcurrent, overvoltage, short circuit, or thermal overload. Compare these features to ensure the component meets your application's safety and reliability requirements. Always verify the specific protection mechanisms in the datasheet.

Specifies the highest input voltage the component can safely handle without damage or malfunction. Compare this value with your power supply output and any transient spikes. Always verify against the datasheet's absolute maximum ratings to ensure reliable operation.

Defines the lowest current threshold at which a protection circuit activates, such as in power supplies or motor drivers. Helps ensure safe operation under fault conditions. Check the datasheet for exact values and tolerances.

Indicates how closely the component's output matches its specified value, critical for sensors, ADCs, and voltage references. Higher accuracy reduces measurement error. Always compare with the datasheet's accuracy specifications for your application.

Specifies how many independent voltage regulator circuits are integrated in the component. Compare this when selecting multi-output power management ICs. Verify against the datasheet to ensure the regulator count matches your design requirements.

Dropout voltage is the minimum input-to-output differential required for a regulator to maintain regulation. Compare this value when selecting LDOs for battery-powered or low-headroom designs. Verify it against the datasheet to ensure your input supply stays above the dropout threshold under load.

Indicates how well a component attenuates power supply noise from input to output. Compare values for stable operation in sensitive analog circuits. Verify against datasheet conditions, as PSRR varies with frequency and load.

Specifies the first regulated output voltage of a multi-output power supply or DC-DC converter. Engineers compare this value to the load requirements and verify it against the datasheet's tolerance and ripple specifications to ensure proper system operation.

Specifies the designed output voltage level under standard operating conditions. Compare this value with your circuit requirements and verify against the datasheet's tolerance and load regulation to ensure compatibility with your application.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.