FL7701MX PMIC - LED Drivers от ON Semiconductor

Indicates the number of switches integrated inside the component. This is critical for power management ICs, multiplexers, or relay drivers where the internal topology determines external wiring. Verify against the datasheet to ensure the device matches your circuit's switching requirements.

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Indicates whether the display can be driven in a multiplexed mode, reducing the number of I/O pins required. This is important for microcontroller-based designs with limited pins. Check the datasheet for maximum multiplexing ratio and refresh rate requirements.

Specifies the total count of individually controllable display segments in LED or LCD panels. Engineers compare this to ensure the driver or controller matches the display configuration. Verify against the datasheet to avoid mismatched pinouts or incorrect multiplexing.

Specifies the lowest DC supply voltage at which the component is guaranteed to operate correctly. Compare this value with your system's power rail to ensure reliable startup and stable performance. Always verify against the datasheet's recommended operating conditions.

Specifies the lowest alternating current voltage at which the component reliably operates. Compare this value with your power supply's output to ensure proper startup and stable performance. Always verify against the datasheet for your specific application conditions.

Specifies the highest alternating current voltage that can be safely applied to the input terminals. Exceeding this limit may damage the component. Verify this value against the datasheet for your specific application to ensure reliable operation.

Specifies the internal circuit architecture of the power converter, such as flyback, forward, or buck. This determines efficiency, isolation, and component stress. Engineers must verify topology against the datasheet to ensure it matches the intended application and operating conditions.

Describes the method or capability for adjusting brightness in LED drivers, lighting controllers, or display backlights. Common methods include analog, PWM, or digital interfaces. Engineers compare dimming options to ensure compatibility with control signals and required dimming range.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Maximum power the component can safely dissipate as heat without exceeding its thermal limits. Compare this rating with your application's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves and ambient temperature conditions.

Specifies the electrical form of the output signal, such as digital, analog, or open collector. This determines how the component interfaces with your circuit. Verify the output type against your system requirements and the datasheet to ensure proper signal compatibility and avoid logic level mismatches.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Specifies how many independent output channels the component provides. Compare this when selecting power supplies, drivers, or modules to ensure the device can drive all required loads. Always verify against the datasheet for exact output configuration.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Specifies the lowest output voltage the component can reliably provide under specified conditions. Compare this value with your circuit's minimum required voltage to ensure proper operation. Always verify against the datasheet's electrical characteristics and test conditions.

Current supplied at the output, indicating the load-driving capability of the component. This is crucial for ensuring the component can drive downstream circuitry without overheating or voltage drop. Compare with your load requirements and check the datasheet for maximum ratings.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Maximum current drawn from the power supply under specified operating conditions. Compare this value across similar components to estimate power consumption and thermal load. Always verify against the datasheet for your exact supply voltage and load scenario.

Specifies the highest continuous current the device can supply at its output without exceeding thermal or electrical limits. Compare this value with your load requirements and derating curves. Always verify against the datasheet for your operating conditions.

Specifies the physical weight of the electronic component, important for logistics, shipping cost, and mechanical design. Verify the exact weight in the datasheet or packaging information, as it may vary with packaging type and quantity.

Maximum power the component can safely dissipate as heat without damage. Exceeding this may cause failure. Check datasheet for thermal resistance and derating curves under your operating conditions.

Specifies the maximum current the output can source when the logic level is high. This is critical for driving loads such as LEDs, relays, or logic inputs. Check this value against your load requirements to avoid output saturation or damage.

Select the component category that best matches your application, such as resistor, capacitor, diode, or connector. This classification helps narrow down the correct part family and ensures compatibility with your circuit design. Verify the type against the datasheet to avoid mismatches.

Specify the typical end-use scenarios for this electronic component, such as consumer electronics, automotive, industrial, or telecommunications. This helps engineers quickly assess suitability for their design. Verify against the datasheet's application section.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Specifies the current the device can sink when its output is driven to a low logic state. Compare this value with the input current of connected loads to ensure reliable logic levels. Verify against the datasheet for maximum ratings and temperature effects.

Specifies the regulated voltage level available at the output pin under specified load and input conditions. Compare this value with your circuit requirements and verify against the datasheet's tolerance and temperature derating.

Minimum voltage required at the input for the component to operate correctly. Below this level, the device may not function or may produce incorrect outputs. Verify that your power supply provides at least this voltage under all load conditions.

Maximum voltage that can be applied to the input without causing damage or malfunction. Exceeding this limit may lead to breakdown or reduced reliability. Always compare with your supply voltage and check the datasheet for absolute maximum ratings.

Specifies the highest voltage the device can deliver at its output under specified conditions. Compare this limit with your application's supply and load requirements to ensure safe operation and avoid overvoltage damage.

Specifies the maximum current each output channel can source or sink continuously. Compare this value with your load requirements to ensure the driver or amplifier can handle the current without overheating or damage. Always verify against the datasheet for absolute maximum ratings and derating curves.

Indicates the rate at which the power device toggles between on and off states. Higher frequencies allow smaller magnetics but increase switching losses. Verify this parameter against your application's requirements and the datasheet's recommended operating conditions.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Operating frequency of the component, typically the clock or switching frequency. This determines the speed of operation and affects power dissipation and signal integrity. Verify the frequency range against your application's requirements and the datasheet specifications.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.