EPM570T100C4N Embedded - PLDs (Programmable Logic Device) от Intel

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Indicates the total storage capacity of the memory device, typically in bits or bytes. Buyers use this to match firmware or data storage requirements. Confirm the exact organization and density in the datasheet before design-in.

Time from when the input signal crosses its threshold until the output begins to turn on. This parameter affects switching speed and power dissipation in high-frequency circuits. Verify it against the datasheet for your specific load and drive conditions.

Specifies the time interval between an input transition and the corresponding output transition. Critical for timing analysis in digital circuits. Verify against datasheet for specific test conditions, supply voltage, and load capacitance.

Describes the logical or electrical function performed by the output pin, such as push-pull, open-drain, or tri-state. This affects how the output interfaces with other circuits. Verify the output type and drive capability in the datasheet.

Indicates whether the component supports JTAG boundary scan testing, a method for verifying interconnections on PCBs. Essential for complex digital ICs in high-reliability applications. Confirm support in the datasheet to plan test strategy and debug access.

Maximum operating frequency specifies the highest clock or switching rate at which the component reliably functions. Designers verify this limit against their application's timing budget to avoid signal integrity issues and ensure stable operation over temperature and voltage variations.

Shows if the component can be programmed after being soldered onto the PCB, without removal. Useful for field updates and prototyping. Verify programming interface and voltage requirements in the datasheet.

Speed grade indicates the maximum operating frequency or propagation delay category for digital ICs, memory, or programmable logic. Compare grades when selecting parts for timing-critical designs. Verify the exact speed rating in the datasheet to ensure it meets your system's clock and signal integrity requirements.

Indicates the total number of input/output pins that can be configured by the user. This is critical for FPGA, CPLD, and microcontroller designs. Verify against the datasheet to ensure sufficient I/O for your application.

Total count of logic array blocks in the FPGA or CPLD. More blocks generally mean more logic capacity. Compare with your design's resource requirements and verify against the device datasheet.

Indicates the total count of programmable logic elements or cells in the FPGA or CPLD. This parameter determines the device's logic capacity and complexity. Compare this value with your design requirements to ensure sufficient resources. Always verify against the datasheet for exact specifications.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Describes the method used to connect the component to the circuit board, such as solder, press-fit, or wire wrap. This affects assembly processes, reliability, and repairability. Check the termination type against your PCB footprint and soldering process to ensure compatibility.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Terminal pitch is the center-to-center distance between adjacent leads or pads on a component. It determines PCB layout compatibility and soldering feasibility. Verify against the datasheet to ensure your footprint matches the component's actual lead spacing.

Specifies the lowest DC input voltage at which the component reliably operates. Compare this value with your system's power rail tolerances and the device's recommended operating conditions to ensure stable performance across all load and temperature ranges.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Defines the underlying technology used for data storage, such as SRAM, DRAM, or Flash. Determines volatility, speed, and endurance. Choose based on your application's need for persistence and access speed.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Total number of input/output pins or channels available on the device. Determines connectivity and interface capability. Verify against your system requirements and datasheet to ensure sufficient I/O for your application.

Typical current drawn from the supply under nominal operating conditions. Compare this value across similar components to estimate power consumption and thermal behavior. Always verify against the datasheet for your specific voltage and load conditions.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

The amount of current the device draws from its power supply during normal operation. This is essential for power budget calculations, thermal management, and selecting appropriate power sources. Check datasheet for typical and maximum values under specified conditions.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Defines the operating temperature range classification for the component, such as commercial, industrial, or automotive. This indicates the environmental conditions the device can withstand. Ensure the grade matches your application's ambient temperature requirements.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Operating frequency of the component, typically the clock or switching frequency. This determines the speed of operation and affects power dissipation and signal integrity. Verify the frequency range against your application's requirements and the datasheet specifications.

Lists any extra characteristics or capabilities beyond the standard specifications, such as built-in protection, special mounting options, or enhanced performance. Review these features to ensure they meet your application's specific needs and compare them across similar parts.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the total number of macro cells in a CPLD or FPGA, which determines the logic capacity and complexity of designs you can implement. Compare this value against your required logic functions and check the datasheet for exact architecture and routing constraints.