2-1658012-2 Rectangular Connectors - Arrays, Edge Type, Mezzanine (Board to Board) от TE Connectivity

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies how many rows of contacts the connector has, typically one, two, or more. This affects the connector's footprint, pin count, and mating force. Choose the row count based on your PCB layout and required pin density. Verify with the datasheet for exact row spacing.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Describes the arrangement and spacing of electrical contacts on the printed circuit board footprint. This attribute is critical for ensuring proper soldering and electrical connection. Verify against the recommended PCB layout in the datasheet to avoid assembly issues.

Indicates the physical mounting orientation of the connector relative to the PCB or mating direction. Engineers compare this to ensure proper alignment in the assembly. Verify against the datasheet for correct placement and mating.

Indicates compliance with the European End-of-Life Vehicle directive, restricting hazardous substances in automotive components. Verify this attribute when sourcing parts for vehicles to ensure environmental and regulatory compliance. Check the datasheet or certificate for specific ELV status.

Reliability rating or qualification indicates the component's expected performance under specified conditions over time. Compare reliability levels when selecting parts for critical applications, and verify the qualification standard against the datasheet to ensure it meets your requirements.

Specifies how many separate conductive paths are inside the component, such as wires in a cable or traces in a connector. This affects current capacity and signal routing. Verify against the datasheet for proper circuit design and compatibility.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

A physical feature on connectors or housings that ensures correct mating orientation. This prevents mismating and potential damage. Verify the key type and position against the datasheet to ensure compatibility with your mating connector and application.

Specifies whether the electrical contact is male (pin) or female (socket). This determines mating compatibility with the corresponding connector half. Verify the gender against the connector housing and mating part to ensure proper insertion and reliable electrical connection.

Specifies the metal alloy used for the electrical contact surfaces, affecting conductivity, wear resistance, and corrosion behavior. Compare materials like silver, gold, or palladium for signal integrity and durability. Verify against datasheet for application-specific requirements.

Indicates the resistance between insulated conductors or contacts, typically measured in megohms. High values ensure minimal leakage current and safe operation. Check datasheet for minimum acceptable levels under specified test conditions.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the material of the component's outer casing, such as plastic, metal, or ceramic. This affects durability, thermal performance, and environmental resistance. Verify against datasheet for application-specific requirements like flammability or chemical exposure.

This attribute highlights special characteristics or functions of the component, such as built-in protection, mounting style, or unique performance traits. Engineers compare these features to match specific application requirements. Always verify against the datasheet for complete specifications.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Specifies the connector series or family, such as USB, RJ45, or D-Sub. This determines mechanical compatibility, pin layout, and mating standards. Verify against the datasheet to ensure the connector matches your board design and mating counterpart.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Total number of contact positions in the connector. This determines the maximum number of electrical connections possible. Compare with your circuit requirements and verify against the datasheet to ensure the connector matches your pin count and layout.

Indicates the number of mating cycles a connector can endure before electrical or mechanical failure. Compare this value when selecting connectors for frequent insertion and removal. Verify the rated cycles in the datasheet to ensure long-term reliability in your application.

The center-to-center distance between adjacent contacts in a connector. Pitch determines the connector's size and PCB footprint requirements. Smaller pitch allows higher density but may require more precise manufacturing. Verify pitch matches your board layout and mating connector to ensure reliable connections.

Describes the method used to connect the component to the circuit board, such as solder, press-fit, or wire wrap. This affects assembly processes, reliability, and repairability. Check the termination type against your PCB footprint and soldering process to ensure compatibility.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Specifies the opposition to alternating current in a component, typically for RF or high-speed signal paths. Compare values to ensure proper impedance matching and signal integrity. Verify against the datasheet for your application frequency.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Specifies the maximum voltage that the insulation between conductors can withstand without breakdown. Critical for safety and reliability in power supplies, transformers, and connectors. Engineers must verify this rating against the datasheet for their application's isolation requirements.

Specifies the center-to-center distance between rows of contacts in a multi-row connector. This dimension is critical for PCB layout and mating with standard headers. Verify against the datasheet to ensure compatibility with your board design and connector housing.

Specifies the overall height of two mated connectors, from the mounting surface of one to the other. Critical for board-to-board spacing and enclosure fit. Verify against the datasheet to ensure proper clearance and mechanical compatibility in your assembly.

Specifies the plating thickness on the mating contact surface, which affects durability, corrosion resistance, and insertion cycles. Compare values across connectors to ensure reliable electrical contact and long-term performance. Verify against the datasheet for your application.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates the color of the component's outer housing, which may aid in visual identification and inventory management. Verify the color against the manufacturer's datasheet or product photos, as it does not affect electrical performance but may be important for assembly or aesthetic requirements.

Specifies how many parallel rows of pins or pads the component footprint occupies on the PCB. This affects board layout, routing, and mechanical fit. Verify against the recommended footprint in the datasheet to ensure proper mounting and soldering.

Describes the physical arrangement of contacts within the connector housing, such as rows and columns. This affects mating compatibility and PCB layout. Always check the pattern against your mating connector and board footprint to ensure proper alignment and avoid assembly issues.

Specifies the plating material on the contact surface, affecting conductivity, corrosion resistance, and durability. Compare finishes like gold, tin, or silver for mating cycle requirements and environmental exposure. Verify the exact finish and thickness in the datasheet to ensure reliable performance in your application.

Indicates whether the component can be sealed to protect against moisture, dust, or other environmental factors. Relevant for connectors, switches, and enclosures used in harsh environments. Verify sealing capability with the manufacturer's specifications.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Indicates the presence of alignment features, such as guides or notches, that ensure correct orientation and positioning during PCB assembly. Verify the specific feature type and dimensions in the datasheet to confirm compatibility with your pick-and-place equipment and board layout.

Specifies the plating thickness on the contact surface, which affects durability, corrosion resistance, and mating cycle life. Compare values across similar connectors to ensure reliable performance in your application, and verify against the datasheet for exact specifications.

Specifies the total number of electrical contact points in the connector. This determines the maximum number of circuits that can be connected. Verify against the datasheet to ensure it matches your required pin count and mating connector configuration.

Specifies the thickness of the metal plating on connector contacts or terminals. Thicker plating generally improves corrosion resistance and durability. Verify this value against the datasheet when selecting parts for harsh environments or high mating cycle applications.

Indicates the mechanical method used to align connector halves during mating, such as keying or polarization. This ensures correct orientation and prevents misconnection. Verify the alignment type against the datasheet to ensure compatibility with your mating connector and application requirements.

Defines the maximum continuous current that a single contact can safely carry. Exceeding this rating may cause overheating, contact degradation, or failure. Check the datasheet for derating curves and ambient temperature effects.

Specifies the total height when multiple components are stacked vertically. This dimension is critical for board clearance and mechanical fit in dense assemblies. Verify against the datasheet to ensure proper enclosure and mating with adjacent parts.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Height above board is the vertical distance from the PCB surface to the top of the component. This dimension is essential for mechanical fit in enclosures and for ensuring clearance under other components. Always check this value against your assembly's height constraints.

Measures the physical depth of the connector body from front to back, excluding any mounting hardware or contacts. This dimension is critical for ensuring proper clearance in enclosures and mating with other components. Verify against the datasheet for exact tolerances and mounting considerations.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.