V23079E1206B301 Signal Relays, Up to 2 Amps от TE Connectivity

Method used to terminate the contact, such as solder, crimp, or press-fit. This determines how the component connects to the PCB or wire. Choose the termination type based on your assembly process and reliability requirements. Confirm with the datasheet for compatibility.

Manufacturer name as listed in the IHS database. Use this attribute to identify the original component maker when cross-referencing parts across distributors. Verify the manufacturer to ensure authenticity and traceability, especially for critical or regulated applications.

Specifies the lowest ambient temperature at which the component reliably functions. Engineers compare this limit to their application's thermal environment to ensure performance and longevity. Always verify against the datasheet's absolute maximum ratings and derating curves.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates the component's compliance with the Restriction of Hazardous Substances directive. Essential for regulatory compliance in many markets. Verify the code against the latest datasheet or certificate to ensure the part meets environmental standards for your application.

Lists any extra characteristics or capabilities beyond the standard specifications, such as built-in protection, special mounting options, or enhanced performance. Review these features to ensure they meet your application's specific needs and compare them across similar parts.

Specifies whether the coil or input circuit is designed for AC or DC supply. This determines the drive circuit compatibility and must match your control voltage. Verify the rated voltage and frequency against the datasheet to ensure proper operation.

Indicates the maximum voltage that can be applied across open contacts without causing an arc or breakdown. Critical for relay and switch isolation ratings. Verify against datasheet for safety margins in your application.

Specifies the method used to control input switching, such as AC, DC, or pulse. This determines how the device is triggered and affects compatibility with your control signal. Verify the required control type against your application's drive circuit and the datasheet specifications.

Specifies whether the contact or output is powered by AC or DC. This determines the required control circuit and load compatibility. Verify against the datasheet to ensure correct polarity and voltage range for your application.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

This is the maximum voltage that can be applied between the relay coil and its contacts without causing insulation breakdown. It ensures safe isolation between control and switching circuits. Verify this rating against the datasheet for your application's voltage requirements.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the packaging format for delivery, such as tube, reel, tray, or tape and reel. This affects handling, storage, and assembly processes. Verify the packing method against your production requirements and the datasheet to ensure compatibility with your pick-and-place equipment.

Indicates the industry specification or standard the component complies with, such as IEC, MIL, or JEDEC. Buyers use this to ensure regulatory and quality compliance. Verify the exact standard and revision against the datasheet before design-in.

Harmonized Tariff Schedule code used for customs classification of electronic components. Helps determine duties and regulatory requirements. Buyers should confirm the code with a customs broker for accurate shipping.

Voltage standing wave ratio indicates how well the component's impedance matches its transmission line. Lower values mean better matching and less signal reflection. Compare VSWR across similar parts to ensure efficient power transfer in RF systems, and verify against the datasheet for your operating frequency.

Specifies the contact arrangement of the relay, such as SPST, SPDT, or DPDT. This determines how many circuits the relay can switch and in what configuration. Verify the form against your application requirements to ensure proper switching functionality.

Number of switching operations under rated load before failure. Compare across relays, switches, and connectors to ensure longevity in your application. Verify against datasheet for specific load conditions and expected endurance.

Mounting type: surface mount or through-hole. Surface mount components are placed directly on the PCB, saving space and enabling automated assembly. Through-hole components offer stronger mechanical bonds. Verify the mounting style matches your PCB design and assembly process.

Specifies the switching behavior of the relay, such as latching or non-latching. This determines how the relay responds to control signals and whether it maintains its state after power is removed. Verify against the datasheet for proper circuit design.

Specifies the plating material on the contact surface, affecting conductivity, corrosion resistance, and solderability. Compare across parts to match application requirements. Verify the exact plating thickness and composition in the datasheet, as it impacts long-term reliability and performance.

Total number of drilled holes in the PCB footprint for through-hole mounting or connector pins. Compare this count with your assembly drawing to ensure the board layout matches the component's mechanical dimensions and pin pattern.

Indicates the component's compliance status with the EU REACH regulation. Buyers should verify this code against the manufacturer's declaration to ensure restricted substances are within allowable limits for their target market.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Describes special mechanical characteristics for mounting, such as through-hole, surface mount, or specific clips. Ensures compatibility with your PCB layout and assembly process. Confirm before designing the footprint.

Specifies the metal or alloy used for the end contacts of a component, such as a resistor or fuse. This affects solderability, corrosion resistance, and long-term reliability. Verify against the datasheet for harsh environments or high-temperature applications.

Specifies the electrical switching configuration of the relay, such as SPDT or DPDT. This determines how many circuits the relay can control and in what sequence. Verify the exact function against the datasheet to ensure it matches your application's switching requirements.

Measure the widest dimension of the component body, excluding leads and terminals. This attribute helps determine PCB footprint compatibility and mechanical fit. Verify against the datasheet drawing for accurate placement and clearance in your assembly.

Release time is the interval from removing coil power until contacts fully open. It affects switching speed and sequencing in control circuits. Verify against datasheet for relay or contactor applications where timing is critical.

Classifies the relay by construction or application, such as electromechanical, solid state, or latching. Helps select the right relay for your switching needs. Refer to the datasheet for specific characteristics and ratings.

Indicates the method used to protect the component from moisture, dust, and other environmental contaminants. Compare sealing types when operating conditions are harsh. Verify the specific sealing standard or rating in the datasheet to ensure reliability in your application.

Operate time is the interval from applying power to the coil until the contacts fully close. It is critical for timing-sensitive circuits and relay sequencing. Verify this value in the datasheet to ensure your application meets switching speed requirements.

Overall dimensions of the component, including length, width, and height. Essential for PCB layout and enclosure design. Confirm these measurements against the datasheet to ensure proper fit and clearance in your assembly.

Maximum DC voltage that can be safely applied across the contacts of a relay, switch, or connector. Exceeding this rating may cause arcing or insulation breakdown. Always verify this limit against the datasheet for your specific load conditions.

Specifies the physical enclosure type and dimensions of the component, such as SOT-23 or QFN. Essential for PCB layout and assembly. Verify against the datasheet to ensure compatibility with your design and manufacturing process.

Specifies the physical weight of the electronic component, important for logistics, shipping cost, and mechanical design. Verify the exact weight in the datasheet or packaging information, as it may vary with packaging type and quantity.

Specifies the highest frequency at which the component reliably meets its electrical specifications. Compare this value with your application's signal frequency to ensure proper performance. Always verify against the datasheet for derating or environmental conditions.

Nominal voltage required to energize the relay coil and switch the contacts. Critical for driving circuits and ensuring reliable operation. Check the datasheet for allowable voltage range and coil resistance to avoid overheating or insufficient actuation.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Contact resistance measures the electrical resistance at the interface between mating contacts. Lower values indicate better conductivity and less heat generation. Compare this parameter across connectors, relays, and switches to ensure reliable signal integrity and power transfer. Always verify against the datasheet for your specific application.

Specifies the highest ambient temperature at which the component can operate reliably. Exceeding this limit may cause performance degradation or permanent damage. Always verify this value against the datasheet for your application's thermal environment.

Indicates the overall risk level of the component based on supply chain, compliance, and reliability factors. Buyers should compare this ranking to assess potential procurement risks and verify details in the datasheet or manufacturer documentation.

Total count of electrical connection points on the component, including pins, leads, or pads. Determines footprint and wiring complexity. Essential for PCB design and ensuring the part matches your circuit schematic and assembly requirements.

Unique alphanumeric identifier assigned by the original manufacturer to specify a particular component version. Use this number to cross-reference datasheets, verify exact specifications, and ensure compatibility with your design. Always confirm it matches the part you intend to order.

Specifies the highest alternating current the contacts can safely carry under normal operating conditions. Compare this value with your circuit's expected AC load to ensure reliable switching and avoid overheating. Always verify against the datasheet for derating factors and temperature limits.

Specifies the DC voltage at which the relay coil reliably energizes and the contacts switch. Compare this value with the coil release voltage and the circuit supply to ensure proper operation. Verify against the datasheet for tolerance and temperature effects.

Height of the switch body from the mounting surface to the top, excluding the actuator. Critical for clearance in enclosures and for PCB assembly. Verify it matches your mechanical design constraints and soldering process requirements.

Identifies the product family or series as designated by the original manufacturer. Use this to group similar components with shared specifications and to locate the correct datasheet. Verify the series matches your design requirements before ordering.

Indicates the current production status of the component, such as active, obsolete, or end-of-life. Buyers should verify this to ensure long-term availability and avoid last-time buy risks. Check the manufacturer datasheet for the most accurate status.

Indicates the resistance between insulated conductors or contacts, typically measured in megohms. High values ensure minimal leakage current and safe operation. Check datasheet for minimum acceptable levels under specified test conditions.

Specifies the highest DC voltage that can be applied to the relay coil without damage. Verify this against the datasheet to ensure your control circuit matches the relay's operating range and avoids overheating or failure.

Specifies the highest continuous direct current the contact can safely carry without overheating or degrading. Compare this rating with your circuit's expected load, and verify it against the datasheet for derating curves and ambient temperature conditions.

Maximum signal attenuation introduced by the component in its intended circuit. Lower values indicate better performance. Compare this parameter across similar parts to ensure your signal integrity requirements are met. Always verify against the datasheet's test conditions, as frequency and impedance can affect the measurement.

Power consumed by the relay coil when energized at its nominal voltage. Compare this value to ensure the coil's heat dissipation is within the relay's thermal limits. Verify against the datasheet for your specific coil voltage and operating conditions.

Maximum AC voltage that can be safely applied across the contacts of a relay, switch, or connector. Exceeding this rating may cause arcing or insulation breakdown. Always verify this limit against the datasheet for your specific load conditions.

Specifies the physical size of the component body, either its length for rectangular parts or diameter for cylindrical ones. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure clearance and proper mounting in your enclosure or assembly.

Specifies the DC resistance of the relay coil, which determines the current draw and power consumption at the rated voltage. Engineers compare this value to ensure the relay driver circuit can supply sufficient current and to calculate coil power dissipation. Verify against the datasheet for proper operation.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.