S29GL128S10TFI010 Memory от Cypress Semiconductor

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies the material of the component's outer casing, such as plastic, metal, or ceramic. This affects durability, thermal performance, and environmental resistance. Verify against datasheet for application-specific requirements like flammability or chemical exposure.

Total number of electrical contacts in the connector, which determines the maximum number of circuits that can be connected. This is a critical parameter for matching the connector to your wire harness requirements. Ensure the contact count aligns with your signal and power needs.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Bit width of digital data processed by a converter, processor, or memory. Higher bits mean better resolution or precision. Verify against datasheet to match your system's data width and accuracy needs.

Electrical resistance value in ohms, defining opposition to current flow. Critical for current limiting, voltage division, and signal conditioning. Always check tolerance and power rating in the datasheet for reliable circuit operation.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Identifies the conversion architecture, such as ADC, DAC, or DC-DC. This determines the signal path, interface, and performance characteristics. Verify the type matches your system's analog or digital conversion needs before selecting the part.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Indicates whether the device is ready to accept commands or busy processing. Check this status pin or register before initiating operations to avoid communication errors. Verify timing and logic levels in the datasheet for reliable system integration.

Indicates whether the component operates in synchronous or asynchronous mode. This affects timing, clocking, and data transfer protocols. Verify the mode against your system requirements and the datasheet to ensure proper integration and performance.

Specifies the number of bits in a single data word for memory or processor components. Compare word sizes when selecting devices for data throughput and processing capability. Verify the exact word size in the datasheet to ensure compatibility with your system architecture.

Specifies the number of bits the driver can handle, indicating the width of the data path or the number of channels. This determines the maximum data throughput and the number of outputs. Ensure it matches your system's bus width or channel requirements.

Specifies the number of sectors and their individual size for rotary switches or encoders. This attribute helps engineers determine the number of positions and the angular spacing between them. Verify against the datasheet to ensure compatibility with your control panel or circuit design.

Maximum current drawn by the component when in standby or sleep mode. Lower values extend battery life in portable designs. Verify against datasheet conditions, as standby current can vary with supply voltage and temperature.

Indicates the maximum continuous wave input power the component can safely handle without damage or excessive distortion. Exceeding this limit may cause failure. Verify this value against your signal power and consider peak-to-average ratio in modulated systems.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Classification of field-effect transistor based on channel polarity and mode, such as N-channel or P-channel, enhancement or depletion. This determines the required gate drive polarity and circuit topology. Engineers select the appropriate type for switching or amplification applications. Always confirm the exact type from the datasheet before design.

Specifies the connector or contact style, such as pin, socket, or blade. This determines mating compatibility and mechanical fit. Verify against the datasheet to ensure correct pairing with the mating connector and proper application.

Indicates the flammability classification of the insulating material used in the component, typically following UL 94 standards. This rating helps engineers assess fire safety and compliance with regulatory requirements. Check the datasheet for the specific test method and thickness conditions.

Specifies the companding algorithm used for signal compression and expansion, such as A-law or μ-law. This affects the signal-to-noise ratio and dynamic range in audio or telecommunication systems. Verify the companding law matches the system requirements and the datasheet.

Nominal capacitance of the diode, typically measured at a specified reverse voltage and frequency. This parameter is important for high-frequency applications, affecting switching speed and signal integrity. Check the datasheet for the test conditions and ensure the capacitance meets your circuit design.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Specifies the maximum time required for a diode or rectifier to switch from conducting to blocking state. This parameter is critical for high-frequency rectification and switching power supplies. Compare this value to minimize switching losses and improve efficiency.

Indicates how much a key parameter, such as voltage or resistance, changes per degree Celsius. Lower values mean better stability across temperature. Verify this against your operating temperature range to ensure consistent performance in your environment.

This attribute indicates how the cable is terminated at its end, such as stripped, tinned, ferrule, or connectorized. It affects the ease of installation, reliability of the connection, and compatibility with terminal blocks or other components. Buyers should select the appropriate type based on the application and verify with the datasheet.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Specifies the smallest erasable block size in memory devices. Compare sector sizes when selecting flash or EEPROM for firmware updates or data storage. Verify against the datasheet to ensure compatibility with your file system and wear-leveling requirements.

The minimum gate-to-source voltage that makes the device start conducting. Compare this value across parts to ensure your drive circuit can reliably turn the switch on. Always verify against the datasheet for your operating temperature.

Specifies the duration needed to program a single word or a page in non-volatile memory. Compare this timing when selecting EEPROM or flash devices for write-intensive applications. Verify against the datasheet to ensure your system meets the required write throughput.

Defines the operating temperature range classification for the component, such as commercial, industrial, or automotive. This indicates the environmental conditions the device can withstand. Ensure the grade matches your application's ambient temperature requirements.

Specifies the maximum data transfer rate the component can handle, typically in bits per second. Compare this value with your system's required throughput to ensure adequate bandwidth. Verify against the datasheet for exact conditions and supported protocols.

Indicates the largest wire size that can be terminated or accommodated by this connector or terminal. Compare with your application's wire gauge to ensure proper fit and reliable electrical contact. Verify against the datasheet for specific wire ranges and strip lengths.

Maximum gate threshold voltage at a specified drain current. This parameter indicates the gate voltage needed to begin conduction. Compare it with your gate drive voltage to ensure reliable switching. Verify against the datasheet for your operating conditions.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Defines the method used to connect wires on the bottom side of the terminal block, such as solder lug, quick-connect, or PCB pin. This determines how the component mounts and connects to your circuit. Ensure compatibility with your board layout and assembly process.

This attribute specifies the thickness of a flat flexible cable (FFC) or flat circuit board (FCB). It is important for ensuring proper insertion into connectors and for mechanical fit in tight enclosures. Engineers must verify this dimension against the connector's specifications to guarantee reliable contact and avoid damage during assembly.

Allowed deviation from the nominal value, expressed as a percentage. Determines precision of resistors, capacitors, and inductors. Choose tighter tolerance for precision circuits, but verify actual performance in the datasheet.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Highest supply voltage at which the component can operate normally without damage or performance degradation. Exceeding this limit may cause overheating or failure. Always check this parameter against your power supply design to ensure the component operates within its safe voltage range for reliable long-term performance.

Highest data transfer rate the component can reliably support, typically in bits per second. This is critical for serial interfaces, modems, or transceivers. Ensure your application's required data throughput does not exceed this limit to avoid communication errors and performance degradation.

Specifies the triac construction or series, such as standard, snubberless, or logic-level. This affects switching performance, gate sensitivity, and commutation capability. Verify the exact type against the datasheet to ensure compatibility with your circuit's voltage, current, and triggering requirements.

Specifies the category of accessory or add-on part for electronic components. Use this to filter compatible mounting hardware, connectors, or protective covers. Verify the accessory type against the component datasheet to ensure proper fit and function in your application.

Range of maximum data transfer rates supported by the component, expressed in kilobits per second. This indicates the span of possible speeds the device can handle. Compare this range with your system's required throughput to ensure the component can support the necessary communication bandwidth without data loss.

Specifies the typical signal loss introduced by the component under standard conditions. Compare this value across similar parts to match your circuit's allowable attenuation. Always verify against the datasheet for frequency and temperature dependencies.

Total resistance is the end-to-end resistance of a component, such as a potentiometer or resistor network. It defines the maximum resistance available and is critical for circuit design. Verify this value against the datasheet to ensure proper operation.

Programming voltage is the specific voltage required to write or erase data in programmable devices like EEPROMs, flash memory, or microcontrollers. It must be applied precisely during programming; incorrect levels can cause write failures or permanent damage, so always follow the datasheet's programming procedure.

Specifies the physical medium through which signals travel, such as fiber optic, twisted pair, or coaxial cable. This attribute is critical for ensuring compatibility with your network infrastructure and for meeting performance requirements. Verify the media type against your system's specifications and the component datasheet to avoid signal integrity issues.

Specifies the maximum instantaneous output current the device can deliver without damage or shutdown. Compare this limit with your inrush and transient load requirements. Verify against the datasheet's safe operating area and pulse conditions to ensure reliable operation.

Specifies the filter topology or technology used in the component, such as low-pass, high-pass, band-pass, or EMI filtering. This attribute helps engineers select the right filter for signal conditioning or noise suppression. Verify the exact filter type against the datasheet to ensure it meets your circuit requirements.

Maximum voltage that can be applied between drain and source terminals without causing breakdown. Critical for MOSFET selection in power circuits. Verify against datasheet for safe operating area and derating.

Specifies whether the output current flows from the device into the load or from the load into the device. This matters for sourcing versus sinking configurations. Verify against the datasheet to ensure correct circuit topology and avoid reverse current damage.

Total storage capacity of the memory chip, typically expressed in bits or bytes. Compare densities to match your application's code and data requirements. Verify against the datasheet to ensure sufficient headroom for firmware and runtime variables.

This is the on-state resistance between the drain and source terminals of a MOSFET. It affects power dissipation and efficiency. Lower values are preferred for high-current switching. Always check the datasheet for the specified test conditions, as RDS(on) varies with gate voltage and temperature.

Specifies the delay from address or control signal assertion until valid data is available at the output. Critical for memory and FPGA configuration devices. Compare with system clock requirements and verify against datasheet timing diagrams.

Typical current consumed by the component in standby or idle state, measured in milliamperes. This is important for battery-powered or low-power applications. Compare this value with your power budget to ensure the component does not drain excessive current when inactive, affecting overall system efficiency.

Specifies the required power supply voltages for the component. Engineers use this to ensure the board's power rails match the device's needs. Verify against the datasheet's recommended operating conditions to avoid undervoltage or overvoltage issues.