AD7747ARUZ Data Acquisition - ADCs/DACs - Special Purpose от Analog Devices Inc

Specifies the sampling technique in an ADC, affecting how the analog input is captured and held during conversion. Engineers compare this to ensure the ADC meets the required signal acquisition speed and accuracy for their application.

Specifies the electrical or digital format of the output signal, such as analog voltage, current loop, or digital protocol. Engineers compare this to ensure compatibility with downstream circuitry or controllers. Verify the exact format and levels in the datasheet before integration.

Specifies the number of bits used to represent an analog signal digitally, determining the smallest detectable change. Higher resolution improves measurement precision but may affect speed and cost. Check effective number of bits (ENOB) in the datasheet for real-world accuracy.

Defines whether the component is powered by a single, dual, or multiple supply rails, or by a specific source like a battery or regulator. This helps designers plan power distribution and avoid incorrect biasing. Check the datasheet for recommended supply configurations.

Indicates how many analog input channels the device supports. Compare this with your system's sensor or signal requirements. Verify against the datasheet to ensure the device has enough inputs for your application and that input voltage ranges match your signals.

Specifies the binary representation of the digital output signal. This code defines how the device encodes its output state. Engineers compare this to the datasheet to ensure compatibility with the receiving logic and to verify correct decoding of the output data.

Specifies how many independent signal paths or outputs the component provides. Compare this value with your circuit requirements to ensure each channel can be used separately. Verify the channel configuration in the datasheet, as some devices may share pins or have internal connections.

Indicates the required power source, such as AC or DC, for the component. Engineers compare this to ensure compatibility with the system's power architecture. Verify the supply type against the datasheet to avoid incorrect power connections.

Specifies the range of DC or AC input voltage the component requires for proper operation. Engineers compare this to the system power rail to ensure compatibility. Always verify against the datasheet's absolute maximum ratings to prevent damage.

Maximum deviation from ideal linearity in the conversion characteristic. This parameter indicates how accurately the output follows a straight-line response. Compare values across similar converters to assess precision. Verify against the datasheet for guaranteed limits.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Minimum voltage required at the input for the component to operate correctly. Below this level, the device may not function or may produce incorrect outputs. Verify that your power supply provides at least this voltage under all load conditions.

Specifies the communication protocol or interface type used by the component, such as I2C, SPI, UART, or USB. This determines how the device connects to a microcontroller or system. Verify compatibility with your host controller and bus voltage levels before design-in.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Mounting type: surface mount or through-hole. Surface mount components are placed directly on the PCB, saving space and enabling automated assembly. Through-hole components offer stronger mechanical bonds. Verify the mounting style matches your PCB design and assembly process.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Typical current drawn from the supply under nominal operating conditions. Compare this value across similar components to estimate power consumption and thermal behavior. Always verify against the datasheet for your specific voltage and load conditions.

Bit width of digital data processed by a converter, processor, or memory. Higher bits mean better resolution or precision. Verify against datasheet to match your system's data width and accuracy needs.

Maximum voltage that can be applied to the input without causing damage or malfunction. Exceeding this limit may lead to breakdown or reduced reliability. Always compare with your supply voltage and check the datasheet for absolute maximum ratings.

Specifies the communication protocol used by the component for data exchange. Common interfaces include I2C, SPI, UART, CAN, and USB. Verify the supported protocol and voltage levels in the datasheet to ensure compatibility with your system design.

Specifies the regulated voltage level available at the output pin under specified load and input conditions. Compare this value with your circuit requirements and verify against the datasheet's tolerance and temperature derating.

Select the component category that best matches your application, such as resistor, capacitor, diode, or connector. This classification helps narrow down the correct part family and ensures compatibility with your circuit design. Verify the type against the datasheet to avoid mismatches.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates how many analog-to-digital or digital-to-analog conversions the device completes per second. Compare this rate with your system's sampling requirements to ensure real-time data acquisition. Verify the specified rate under the datasheet's operating conditions, as it may vary with clock frequency and supply voltage.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Maximum power the component can safely dissipate as heat without exceeding its thermal limits. Compare this rating with your application's expected power loss to ensure reliable operation. Always verify against the datasheet's derating curves and ambient temperature conditions.

Number of analog signal samples taken per second by an ADC or digital sensor. Determines maximum signal frequency that can be accurately captured. Verify against datasheet for your application's bandwidth needs.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.