1-207303-3 Circular Connectors от TE Connectivity

Specifies the plating thickness on the mating contact surface, which affects durability, corrosion resistance, and insertion cycles. Compare values across connectors to ensure reliable electrical contact and long-term performance. Verify against the datasheet for your application.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Specifies the type of filtering the component provides, such as EMI, RFI, or signal conditioning. Compare this attribute when selecting parts for noise suppression or signal integrity. Verify the exact filter topology and performance against the datasheet.

Surface finish on the contact area that mates with another connector. This finish affects corrosion resistance, contact resistance, and durability. Choose the appropriate finish based on the number of mating cycles and environmental conditions, and verify it in the datasheet.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

UL flammability rating of the material used in the component, indicating its resistance to ignition and flame spread. This is important for safety compliance in end products. Check the rating against your application's required safety standards and environmental conditions.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Specifies whether the electrical contact is male (pin) or female (socket). This determines mating compatibility with the corresponding connector half. Verify the gender against the connector housing and mating part to ensure proper insertion and reliable electrical connection.

Indicates compliance with the European End-of-Life Vehicle directive, restricting hazardous substances in automotive components. Verify this attribute when sourcing parts for vehicles to ensure environmental and regulatory compliance. Check the datasheet or certificate for specific ELV status.

Specifies the metal alloy used for the electrical contact surfaces, affecting conductivity, wear resistance, and corrosion behavior. Compare materials like silver, gold, or palladium for signal integrity and durability. Verify against datasheet for application-specific requirements.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Total number of contact positions in the connector. This determines the maximum number of electrical connections possible. Compare with your circuit requirements and verify against the datasheet to ensure the connector matches your pin count and layout.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Specifies the mechanical method used to secure the component to a PCB or panel, such as screw, snap-in, or adhesive. This affects assembly time, reliability under vibration, and serviceability. Verify compatibility with your mounting process and enclosure design before ordering.

Specifies the maximum continuous current the component can safely carry under specified conditions. Compare this value with your circuit's expected load to ensure reliable operation. Always verify against the datasheet for temperature derating and mounting considerations.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Specifies the visual color of the component body or housing. Useful for identifying parts in inventory or matching design aesthetics. Verify against the datasheet or physical sample, as color may vary between manufacturers and batches.

Specifies the highest alternating current voltage the component can withstand continuously without damage. Compare this rating with your circuit's operating voltage and transients. Always verify against the datasheet for derating factors and safety margins.

Indicates whether the component complies with German DIN standards. Verify this attribute when the application requires specific mechanical, electrical, or safety specifications defined by DIN. Check the datasheet for the exact DIN number and edition to ensure compatibility with your system.

Indicates whether the connector combines different contact types, such as signal, power, or coaxial, in one housing. This attribute helps engineers identify versatile interconnect solutions for complex wiring systems. Verify the exact contact arrangement and ratings in the datasheet before design-in.

Indicates whether the component meets military specifications (MIL-SPEC) for reliability, performance, and environmental resistance. This is critical for defense, aerospace, and high-reliability applications. Verify the specific MIL standard and test conditions in the datasheet.

Indicates whether the component meets International Electrotechnical Commission standards. Check this attribute to ensure compatibility with international safety and performance requirements. Verify the specific IEC standard listed in the datasheet for your application.

Indicates the flammability classification of the insulating material used in the component, typically following UL 94 standards. This rating helps engineers assess fire safety and compliance with regulatory requirements. Check the datasheet for the specific test method and thickness conditions.

Describes the method used to connect the component to the circuit board, such as solder, press-fit, or wire wrap. This affects assembly processes, reliability, and repairability. Check the termination type against your PCB footprint and soldering process to ensure compatibility.

Specifies the voltage range within which the component operates correctly. Check the datasheet to ensure your power supply meets the minimum and maximum limits, as exceeding them can damage the device or cause malfunction.

Indicates the mechanical method used to align connector halves during mating, such as keying or polarization. This ensures correct orientation and prevents misconnection. Verify the alignment type against the datasheet to ensure compatibility with your mating connector and application requirements.

Specifies the total number of electrical contact points in the connector. This determines the maximum number of circuits that can be connected. Verify against the datasheet to ensure it matches your required pin count and mating connector configuration.

Indicates whether the connector shell is supplied without contacts, allowing you to insert your own crimp contacts. This is useful for custom wiring and field assembly. Check the shell's compatibility with the required contact gauge and insertion tooling.

Indicates how many independent connection points or interfaces the component provides. Compare this when selecting connectors, switches, or modules for multi-channel designs. Verify against the datasheet to ensure the port count matches your system's required I/O configuration.

Indicates whether the component can be sealed to protect against moisture, dust, or other environmental factors. Relevant for connectors, switches, and enclosures used in harsh environments. Verify sealing capability with the manufacturer's specifications.

Gender indicates whether a connector is male (with pins) or female (with sockets). This is critical for mating compatibility in cable assemblies and board-to-board connections. Verify gender against the mating connector part number to ensure proper fit and reliable electrical contact.

Indicates how many contact positions in the connector are dedicated to carrying power. Compare this with the total number of positions to ensure the connector meets your power and signal requirements. Verify against the datasheet for proper current rating per contact.

Describes special mechanical characteristics for mounting, such as through-hole, surface mount, or specific clips. Ensures compatibility with your PCB layout and assembly process. Confirm before designing the footprint.

Specifies the maximum rated voltage, current, and power for safe operation. Compare these limits with your circuit requirements to ensure reliability. Always verify against the datasheet for derating curves and environmental conditions.

Specifies the dielectric material used to isolate conductive parts in components such as transformers, connectors, or cables. This affects thermal resistance, voltage withstand capability, and flammability rating. Verify the material against datasheet specifications for safety and performance in your application.

Specifies the base material of the connector shell, determining mechanical robustness, weight, and thermal conductivity. Critical for applications with vibration or temperature extremes. Verify material type and any plating in the datasheet for compatibility.

Indicates the mechanical style or configuration of the backshell used on a circular connector. This affects cable entry, strain relief, and overall assembly fit. Verify compatibility with your connector series and cable diameter before ordering.

Physical depth of the component body, measured in millimeters or inches. This dimension affects PCB layout and mechanical fit. Verify against the datasheet for proper clearance in your enclosure or assembly.

Specifies the thickness of the metal plating on connector contacts or terminals. Thicker plating generally improves corrosion resistance and durability. Verify this value against the datasheet when selecting parts for harsh environments or high mating cycle applications.

Specifies the maximum continuous voltage the component can safely withstand under normal operating conditions. Engineers compare this rating to the circuit's expected voltage to ensure reliable operation. Always verify against the datasheet for derating factors and environmental conditions.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Specifies the connector series or family, such as USB, RJ45, or D-Sub. This determines mechanical compatibility, pin layout, and mating standards. Verify against the datasheet to ensure the connector matches your board design and mating counterpart.

Indicates the physical mounting orientation of the connector relative to the PCB or mating direction. Engineers compare this to ensure proper alignment in the assembly. Verify against the datasheet for correct placement and mating.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Specifies the shell size designation for the insert of a connector. This dimension determines compatibility with mating shells and panel cutouts. Verify against the datasheet to ensure proper fit and mechanical mating before ordering.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Length of the lead or wire extending from the component body, important for through-hole mounting and soldering. This dimension affects how the component sits on the board and the solder joint quality. Verify it matches your PCB hole depth and assembly process.

Overall physical length of the assembled component, including connectors, housing, and any attached leads. Critical for mechanical fit in enclosures or PCB layouts. Always compare with your required clearance and mounting dimensions before ordering.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.