EEE-FC1E331AP Aluminum Electrolytic Capacitors от Panasonic

Specifies the dielectric material or construction technology used in the capacitor, such as ceramic, electrolytic, film, or tantalum. This determines key performance characteristics like capacitance stability, voltage rating, temperature behavior, and ESR. Engineers should verify the type against the datasheet to ensure it meets the application's requirements for reliability and frequency response.

Current that flows through the component when it is in the off-state or reverse-biased. Important for capacitors, diodes, and transistors to minimize power loss and ensure proper isolation. Compare leakage current values to avoid unintended circuit behavior, especially in battery-powered or high-impedance applications. Verify test conditions in the datasheet.

Tan delta indicates the dissipation factor of a capacitor, reflecting energy losses in the dielectric. Lower values mean higher efficiency and stability. Compare this parameter when selecting capacitors for AC applications, and verify it against the datasheet for your operating frequency and temperature.

Capacitance value of the component, typically expressed in farads (pF, nF, µF). This parameter determines energy storage and filtering characteristics. Compare capacitance when selecting capacitors for power supply decoupling, signal coupling, or timing applications. Always check the rated voltage and tolerance in the datasheet.

Standard alphanumeric code indicating component dimensions, such as case size for passives or package type for semiconductors. Compare codes across manufacturers to ensure footprint compatibility. Verify against the datasheet for exact dimensions and tolerances.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Describes the method used to connect the component to the circuit board, such as solder, press-fit, or wire wrap. This affects assembly processes, reliability, and repairability. Check the termination type against your PCB footprint and soldering process to ensure compatibility.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specify the typical end-use scenarios for this electronic component, such as consumer electronics, automotive, industrial, or telecommunications. This helps engineers quickly assess suitability for their design. Verify against the datasheet's application section.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Allowed deviation from the nominal value, expressed as a percentage. Determines precision of resistors, capacitors, and inductors. Choose tighter tolerance for precision circuits, but verify actual performance in the datasheet.

Specifies the maximum DC voltage the component can safely handle under rated conditions. Engineers compare this to the circuit's operating voltage to ensure adequate margin. Always verify against the datasheet's derating curves for temperature and reliability.

Indicates the maximum voltage the component can withstand or operate at, depending on context. Critical for ensuring the part is not overstressed in your application. Always compare with your circuit's voltage levels and consider transient spikes.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Length of the lead or wire extending from the component body, important for through-hole mounting and soldering. This dimension affects how the component sits on the board and the solder joint quality. Verify it matches your PCB hole depth and assembly process.

Indicates the physical configuration of component leads, such as straight, angled, or formed. This affects PCB mounting, clearance, and soldering. Verify the terminal shape against your board layout and assembly process to ensure proper fit and reliable connections.

Specifies the maximum rated voltage, current, and power for safe operation. Compare these limits with your circuit requirements to ensure reliability. Always verify against the datasheet for derating curves and environmental conditions.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Indicates whether the component is polarized or non-polarized. Polarized components, such as electrolytic capacitors and diodes, must be installed in the correct orientation to avoid damage. Non-polarized components can be placed either way. Check the datasheet for proper installation guidelines.

Lists any extra characteristics or capabilities beyond the standard specifications, such as built-in protection, special mounting options, or enhanced performance. Review these features to ensure they meet your application's specific needs and compare them across similar parts.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Insulating material used in capacitors, connectors, or substrates, determining electrical performance, temperature stability, and insulation resistance. Choose among ceramic, tantalum, or polymer types based on capacitance, voltage, and frequency requirements. Always confirm the dielectric specification in the datasheet for your application's operating conditions.

Specifies the packaging format for delivery, such as tube, reel, tray, or tape and reel. This affects handling, storage, and assembly processes. Verify the packing method against your production requirements and the datasheet to ensure compatibility with your pick-and-place equipment.

Operational life rating in hours under specified conditions, often at rated temperature and voltage. This indicates how long the component is expected to function before failure. Verify that this meets your application's endurance requirements.

Recommended PCB land pattern dimensions for surface mount components. This ensures proper solder joint formation and mechanical stability. Always follow the manufacturer's layout guidelines to avoid tombstoning or poor thermal performance.

Maximum AC voltage that the component can safely withstand under specified conditions. This rating is critical for insulation and safety margins. Always compare it with the operating voltage in your circuit and derate according to the datasheet guidelines.

Maximum allowable AC ripple current at low frequency, typically 120 Hz or 1 kHz. Exceeding this rating can overheat the capacitor and shorten its life. Verify against the datasheet for your operating frequency.

Expected operational lifetime of the component at a specified ambient or case temperature. Higher temperatures reduce lifetime. Use this rating to estimate reliability in your application and ensure it meets your product's expected lifespan.

This is the maximum allowable AC ripple current at high frequency for capacitors. It affects heating and lifespan. Compare with your circuit's ripple current and verify against the datasheet for safe operation.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Maximum allowable AC ripple current that the component can handle without overheating or degrading. This is crucial for capacitors in power supplies and converters. Exceeding this rating can reduce lifespan or cause failure. Always verify against the datasheet for your operating conditions.

Equivalent series resistance indicates internal losses in capacitors and inductors. Lower ESR improves efficiency and reduces heat in power circuits. Compare ESR values when selecting components for high-frequency or high-current applications, and verify against the datasheet for your operating conditions.

Specifies the opposition to alternating current in a component, typically for RF or high-speed signal paths. Compare values to ensure proper impedance matching and signal integrity. Verify against the datasheet for your application frequency.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Distance between centers of adjacent leads on a component. Critical for PCB layout and soldering. Engineers compare this to ensure the part fits the footprint. Verify against the datasheet for accurate mounting.

Physical dimensions of the component, typically length, width, and height. These measurements are critical for PCB layout and mechanical fit. Always verify against the datasheet for exact tolerances and mounting requirements.

Maximum allowable AC ripple current for capacitors, usually specified at a certain frequency and temperature. This rating determines heat generation and reliability. Compare with your circuit's ripple current to ensure adequate derating.

Specifies the physical diameter of the component package, typically for cylindrical parts like capacitors, resistors, or fuses. Verify this dimension against your PCB layout and mechanical clearance requirements to ensure proper fit and assembly.

Maximum vertical dimension from the seating plane to the top of the component body. Critical for PCB clearance and enclosure fit. Verify against the datasheet when designing mechanical constraints or checking compatibility with mating parts.