748365-1 D-Sub, D-Shaped Connectors - Housings от TE Connectivity

Indicates the industry specification or standard the component complies with, such as IEC, MIL, or JEDEC. Buyers use this to ensure regulatory and quality compliance. Verify the exact standard and revision against the datasheet before design-in.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Specifies the dielectric material used to isolate conductive parts in components such as transformers, connectors, or cables. This affects thermal resistance, voltage withstand capability, and flammability rating. Verify the material against datasheet specifications for safety and performance in your application.

Indicates the resistance between insulated conductors or contacts, typically measured in megohms. High values ensure minimal leakage current and safe operation. Check datasheet for minimum acceptable levels under specified test conditions.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Indicates whether the component is manufactured without lead, complying with RoHS and similar regulations. Check this attribute to ensure environmental compliance for your market. Verify against the datasheet for exact material declarations.

Specifies the maximum voltage that the insulation between conductors can withstand without breakdown. Critical for safety and reliability in power supplies, transformers, and connectors. Engineers must verify this rating against the datasheet for their application's isolation requirements.

Total number of contact positions in the connector. This determines the maximum number of electrical connections possible. Compare with your circuit requirements and verify against the datasheet to ensure the connector matches your pin count and layout.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Contact resistance measures the electrical resistance at the interface between mating contacts. Lower values indicate better conductivity and less heat generation. Compare this parameter across connectors, relays, and switches to ensure reliable signal integrity and power transfer. Always verify against the datasheet for your specific application.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Combines the shell base material and its surface finish, providing complete information on mechanical and environmental performance. Essential for selecting connectors in harsh environments. Confirm both material and finish specifications in the datasheet.

This attribute highlights special characteristics or functions of the component, such as built-in protection, mounting style, or unique performance traits. Engineers compare these features to match specific application requirements. Always verify against the datasheet for complete specifications.

Measure the widest dimension of the component body, excluding leads and terminals. This attribute helps determine PCB footprint compatibility and mechanical fit. Verify against the datasheet drawing for accurate placement and clearance in your assembly.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Style or type of the connector, such as D-sub, USB, RJ45, or circular, determining its mechanical interface and electrical performance. Choose the style that matches your mating connector and application environment. Verify the connector style in the datasheet to ensure proper fit, pinout, and durability for your design.

This attribute specifies the center-to-center distance between rows of contacts in a mating connector. It is critical for ensuring mechanical compatibility with the corresponding receptacle and for PCB layout design. Engineers must verify this dimension against the connector's datasheet to avoid misalignment and ensure reliable connections.

Characteristics of the mounting flange on components like connectors, switches, or power modules, affecting mechanical stability and heat dissipation. Features may include hole patterns, material, or plating. Ensure the flange design matches your mounting hardware and thermal management requirements. Consult the datasheet for detailed dimensions and tolerances.

Minimum force required to withdraw a connector from its mating part. Ensures reliable mechanical retention and prevents accidental disconnection. Engineers compare this for applications with vibration or shock. Check datasheet for test conditions.

Specifies the surface plating on contacts or shell, affecting corrosion resistance, solderability, and contact reliability. Choose based on application environment and mating cycles. Verify against datasheet for thickness and material composition.

Provides additional information or remarks about the component that are not covered by other attributes. This may include special handling instructions, application notes, or manufacturer clarifications. Always review this note to avoid overlooking important details that could affect design or assembly.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Specifies the connector series or family, such as USB, RJ45, or D-Sub. This determines mechanical compatibility, pin layout, and mating standards. Verify against the datasheet to ensure the connector matches your board design and mating counterpart.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Indicates the physical shell size and contact arrangement of the connector, often following industry standards like MIL-DTL-5015 or DIN. This determines mating compatibility with corresponding receptacles and panel cutouts. Verify the layout designation against your system's requirements and the datasheet.

Specifies the physical configuration of the electrical contact, such as stamped, formed, or machined. This affects durability, current rating, and mating cycles. Verify the contact design against the datasheet to ensure it meets your application's mechanical and electrical requirements.

Specifies the visual color of the component body or housing. Useful for identifying parts in inventory or matching design aesthetics. Verify against the datasheet or physical sample, as color may vary between manufacturers and batches.

Gender indicates whether a connector is male (with pins) or female (with sockets). This is critical for mating compatibility in cable assemblies and board-to-board connections. Verify gender against the mating connector part number to ensure proper fit and reliable electrical contact.

Indicates the physical mounting orientation of the connector relative to the PCB or mating direction. Engineers compare this to ensure proper alignment in the assembly. Verify against the datasheet for correct placement and mating.

Indicates the surface finish applied to the connector shell, affecting corrosion resistance, shielding effectiveness, and appearance. Choose finish based on environmental exposure and EMI requirements. Check datasheet for plating thickness and adhesion properties.

Specifies the minimum wire gauge or cross-sectional area that the connector terminal can reliably accommodate. Using smaller wires may result in poor contact or insufficient mechanical retention. Check the datasheet to ensure the selected wire size falls within the acceptable range for the terminal.

Specifies the maximum wire gauge or cross-sectional area that the connector terminal can accommodate. This ensures proper crimping and electrical contact. Engineers must verify this limit against the datasheet to avoid using oversized wires that could cause poor connection or damage.

Specifies how many rows of contacts the connector has, typically one, two, or more. This affects the connector's footprint, pin count, and mating force. Choose the row count based on your PCB layout and required pin density. Verify with the datasheet for exact row spacing.

Defines the contact gender and style, such as pin (male) or socket (female). This determines how the connector mates with its counterpart. Ensure the contact type matches your cable or board connector to avoid mismating. Refer to the datasheet for contact material and plating.

Indicates the physical shape and configuration of the connector body or shell, such as circular, rectangular, or D-sub. This affects mounting, mating, and panel cutout requirements. Verify compatibility with your enclosure and mating connector before design-in.

Maximum current rating for signal transmission through the component. This value ensures reliable signal integrity without overheating. Compare it with your circuit's actual signal current to avoid exceeding the limit, and verify derating factors for high-temperature environments.

Describes the method used to connect the component to the circuit board, such as solder, press-fit, or wire wrap. This affects assembly processes, reliability, and repairability. Check the termination type against your PCB footprint and soldering process to ensure compatibility.

Specifies the total number of electrical contact points in the connector. This determines the maximum number of circuits that can be connected. Verify against the datasheet to ensure it matches your required pin count and mating connector configuration.

Insulating material used in capacitors, connectors, or substrates, determining electrical performance, temperature stability, and insulation resistance. Choose among ceramic, tantalum, or polymer types based on capacitance, voltage, and frequency requirements. Always confirm the dielectric specification in the datasheet for your application's operating conditions.

Specifies the metal alloy used for the electrical contact surfaces, affecting conductivity, wear resistance, and corrosion behavior. Compare materials like silver, gold, or palladium for signal integrity and durability. Verify against datasheet for application-specific requirements.

Minimum outer diameter of the wire insulation that the connector or terminal can accommodate. Verify this dimension against your wire specification to ensure a proper fit and reliable crimping. Critical for cable assembly and wire harness design.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Indicates whether the component meets military specifications (MIL-SPEC) for reliability, performance, and environmental resistance. This is critical for defense, aerospace, and high-reliability applications. Verify the specific MIL standard and test conditions in the datasheet.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Distance between centers of mating contacts in a connector. Critical for ensuring mechanical and electrical compatibility with the corresponding receptacle. Verify against the connector's datasheet to avoid mismatches in PCB layout and assembly.

Surface finish on the contact area that mates with another connector. This finish affects corrosion resistance, contact resistance, and durability. Choose the appropriate finish based on the number of mating cycles and environmental conditions, and verify it in the datasheet.

Specifies the physical weight of the electronic component, important for logistics, shipping cost, and mechanical design. Verify the exact weight in the datasheet or packaging information, as it may vary with packaging type and quantity.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.