DG9252EN-T1-E4 Interface - Analog Switches, Multiplexers, Demultiplexers от Vishay

Defines the switch topology, such as 2:1, 4:1, or 8:1, indicating how many inputs are routed to outputs. Essential for selecting the correct multiplexer for signal routing in your design. Check the datasheet for channel count and switching characteristics.

Highest supply voltage at which the component can operate normally without damage or performance degradation. Exceeding this limit may cause overheating or failure. Always check this parameter against your power supply design to ensure the component operates within its safe voltage range for reliable long-term performance.

Typical current consumed by the component in standby or idle state, measured in milliamperes. This is important for battery-powered or low-power applications. Compare this value with your power budget to ensure the component does not drain excessive current when inactive, affecting overall system efficiency.

Indicates the construction or configuration of the transformer, such as flyback, forward, or planar. Affects performance, size, and application suitability. Refer to datasheet for detailed specifications and recommended usage.

Range of maximum data transfer rates supported by the component, expressed in kilobits per second. This indicates the span of possible speeds the device can handle. Compare this range with your system's required throughput to ensure the component can support the necessary communication bandwidth without data loss.

Total resistance is the end-to-end resistance of a component, such as a potentiometer or resistor network. It defines the maximum resistance available and is critical for circuit design. Verify this value against the datasheet to ensure proper operation.

Specifies the physical medium through which signals travel, such as fiber optic, twisted pair, or coaxial cable. This attribute is critical for ensuring compatibility with your network infrastructure and for meeting performance requirements. Verify the media type against your system's specifications and the component datasheet to avoid signal integrity issues.

Specifies the category of accessory or add-on part for electronic components. Use this to filter compatible mounting hardware, connectors, or protective covers. Verify the accessory type against the component datasheet to ensure proper fit and function in your application.

Specifies the maximum continuous voltage the component can safely withstand without damage or performance degradation. Critical for ensuring proper operating margins in power supplies, signal lines, and isolation barriers. Always confirm with the datasheet for absolute maximum ratings.

Specifies the filter topology used in the component, such as low-pass, high-pass, band-pass, or notch. This determines the frequency response and attenuation characteristics. Engineers must verify the filter type against the datasheet to ensure it meets the required signal conditioning and interference rejection for the application.

Specifies the maximum allowable upward deviation from the nominal value for this component parameter. Verify against datasheet limits to ensure your circuit tolerates the worst-case positive variation, especially for resistors, capacitors, and other passives.

Specifies the triac construction or series, such as standard, snubberless, or logic-level. This affects switching performance, gate sensitivity, and commutation capability. Verify the exact type against the datasheet to ensure compatibility with your circuit's voltage, current, and triggering requirements.

Indicates protection features integrated into the component, such as overcurrent, overvoltage, or thermal shutdown. These safeguards help prevent damage during fault conditions. Verify which protections are included and their thresholds in the datasheet to ensure they meet your application's safety requirements.

Indicates whether the component supports automatic software flow control, a method using XON/XOFF characters to manage data transmission. Check this attribute when selecting UARTs, USB bridges, or communication modules to ensure compatibility with your system's flow control requirements.

This attribute provides the component description from the Samacsys library. It summarizes key specifications and features for quick identification. Review it to understand the part's function and compare with the datasheet for detailed parameters.

Material used for the magnetic core in inductors, transformers, or ferrite beads. Affects permeability, saturation current, and frequency characteristics. Choose the right core material for your application's operating frequency and power level to optimize efficiency and avoid saturation.

Specifies the maximum instantaneous output current the device can deliver without damage or shutdown. Compare this limit with your inrush and transient load requirements. Verify against the datasheet's safe operating area and pulse conditions to ensure reliable operation.

Specifies how many analog-to-digital and digital-to-analog converters are integrated in the component. This matters when selecting mixed-signal ICs for data acquisition or control systems. Verify against the datasheet to ensure the converter count matches your application requirements.

Specifies the ambient or case temperature at which the component's electrical and mechanical characteristics are guaranteed. Verify this value against the datasheet to ensure the part operates within its intended thermal environment and to avoid derating issues.

Power supply rejection ratio measures how well a regulator or amplifier attenuates supply noise and ripple. Higher PSRR means cleaner output. Critical for precision analog circuits and RF. Compare at relevant frequencies and load currents.

Typical delay from the moment the turn-off signal is applied until the output begins to transition. This parameter affects switching losses and timing margins in power circuits. Compare with datasheet values to ensure your design meets required switching performance.

Frequency range in which the component operates reliably. Important for RF, switching, and signal processing applications. Ensure your circuit's frequency falls within this range to maintain performance.

Specifies the allowable deviation from the nominal resistance value, expressed as a percentage. Critical for precision circuits where accurate resistance is required. Check datasheet for tolerance range and temperature coefficient.

Minimum forward transconductance value for a transistor or amplifier. Indicates the minimum gain capability. Critical for ensuring sufficient amplification in your circuit. Verify against datasheet conditions.

Indicates the lowest frequency at which the component's response begins to roll off. Compare this value with your signal bandwidth to ensure the part passes desired frequencies. Verify against the datasheet's frequency response curve for your operating conditions.

Indicates the total count of input/output pins or channels available on the component. Engineers compare this to ensure sufficient connectivity for their application. Verify against the datasheet pinout to confirm exact configuration and compatibility with your design.

Indicates whether the UART or serial interface can detect and ignore spurious start bits caused by noise or line glitches. This feature improves communication robustness in noisy environments. Check the datasheet to confirm the detection algorithm and any configuration requirements.

Maximum resistance between the switch terminals when the device is fully on. Lower values reduce power loss and heat. Compare this parameter when selecting MOSFETs, IGBTs, or relays for high-current circuits. Always verify against the datasheet for your operating conditions.

Indicates whether the device automatically manages hardware flow control signals such as RTS and CTS. This feature reduces host processor overhead by handling handshaking in hardware. Verify support in the datasheet when designing UART or serial communication interfaces.

Specifies the maximum allowable decrease from the nominal value for components like resistors, capacitors, or inductors. Engineers compare this to ensure worst-case performance still meets circuit requirements. Always verify against the datasheet for the specific part.

Typical time delay between the input signal and the output activation, usually in nanoseconds or microseconds. This parameter is critical for timing-sensitive circuits. Ensure that the delay meets your system's timing requirements to avoid signal skew or improper switching behavior.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies the material of the component's outer casing, such as plastic, metal, or ceramic. This affects durability, thermal performance, and environmental resistance. Verify against datasheet for application-specific requirements like flammability or chemical exposure.

Allowed deviation from the nominal value, expressed as a percentage. Determines precision of resistors, capacitors, and inductors. Choose tighter tolerance for precision circuits, but verify actual performance in the datasheet.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Time required for the device to transition from off state to fully on state. This parameter is critical for timing analysis in power supplies, drivers, and switching circuits. Verify this value against your system's timing budget and switching frequency requirements.

Bit width of digital data processed by a converter, processor, or memory. Higher bits mean better resolution or precision. Verify against datasheet to match your system's data width and accuracy needs.

Indicates the highest DC or AC voltage that can be safely applied to the power supply pin without risking damage or malfunction. Verify this limit against the datasheet before designing your circuit to ensure reliable operation under all conditions.

Identifies the conversion architecture, such as ADC, DAC, or DC-DC. This determines the signal path, interface, and performance characteristics. Verify the type matches your system's analog or digital conversion needs before selecting the part.

Specifies the packaging format for delivery, such as tube, reel, tray, or tape and reel. This affects handling, storage, and assembly processes. Verify the packing method against your production requirements and the datasheet to ensure compatibility with your pick-and-place equipment.

Defines the operating temperature range classification for the component, such as commercial, industrial, or automotive. This indicates the environmental conditions the device can withstand. Ensure the grade matches your application's ambient temperature requirements.

Specifies the maximum data transfer rate the component can handle, typically in bits per second. Compare this value with your system's required throughput to ensure adequate bandwidth. Verify against the datasheet for exact conditions and supported protocols.

Manufacturer name as listed in the IHS database. Use this attribute to identify the original component maker when cross-referencing parts across distributors. Verify the manufacturer to ensure authenticity and traceability, especially for critical or regulated applications.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Specifies the maximum continuous current the component can safely carry under specified conditions. Compare this rating with your circuit's expected load to prevent overheating or failure. Always verify against the datasheet for temperature derating and mounting considerations.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Specifies the metal alloy used for the electrical contact surfaces, affecting conductivity, wear resistance, and corrosion behavior. Compare materials like silver, gold, or palladium for signal integrity and durability. Verify against datasheet for application-specific requirements.

Specifies the nominal operating voltage that must be applied to the component for proper function. Verify this value against your system's power rail and the datasheet's absolute maximum ratings to ensure reliable operation and avoid damage.

Indicates the maximum voltage the component can withstand or operate at, depending on context. Critical for ensuring the part is not overstressed in your application. Always compare with your circuit's voltage levels and consider transient spikes.

Indicates the depth of the FIFO buffer used in UART or serial communication interfaces. Helps engineers manage data flow and avoid overrun or underrun conditions. Check the datasheet for exact counter behavior and interrupt generation.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the component's compliance status with the EU REACH regulation. Buyers should verify this code against the manufacturer's declaration to ensure restricted substances are within allowable limits for their target market.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Manufacturing technology or process used for the component, such as thin film, thick film, or semiconductor process. Affects performance, stability, and cost. Confirm the technology matches your application requirements and environmental conditions.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.