GI751-E3/73 Diodes - Rectifiers - Single от Vishay

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Small current flowing through a semiconductor junction when reverse voltage is applied. Lower leakage is preferred for precision and low-power circuits. Check this parameter at the specified reverse voltage to ensure it meets your application's requirements.

Indicates how many independent functional sections are integrated into a single component package. This matters when comparing multi-channel devices or resistor networks. Always verify the exact element count against the datasheet to ensure it matches your circuit design requirements.

Number of electrical phases supported by the component, such as single-phase or three-phase. This determines the input power configuration and affects the design of power supplies, motor drives, and rectifiers. Confirm compatibility with your system's phase requirements.

Semiconductor material used in the diode, such as silicon, germanium, or gallium arsenide. Affects forward voltage, speed, and temperature behavior. Choose based on your application's voltage, current, and switching requirements. Verify with datasheet specifications.

Forward voltage is the voltage drop across a diode or LED when it conducts current in the forward direction. It affects power dissipation and efficiency. Compare this value with your circuit's supply voltage and check the datasheet for the specified test current.

Select the diode classification such as Schottky, Zener, or standard rectifier. This defines the device's electrical behavior and typical applications. Verify the exact type against the datasheet to ensure it meets your circuit requirements for voltage, current, and switching speed.

Specifies the highest reverse current that flows through the component when the rated reverse voltage is applied. Compare this value across diodes and rectifiers to ensure minimal leakage and stable operation. Verify against the datasheet for your operating temperature and voltage conditions.

Specifies the maximum continuous DC voltage that can be applied in the reverse direction without causing breakdown. Critical for rectifier and protection diodes. Verify against datasheet to ensure safe operating margin in your circuit.

Indicates the highest repetitive reverse voltage the diode can withstand in blocking mode. Engineers compare this to the circuit's peak reverse stress to ensure reliable operation. Always verify against the datasheet for your specific application.

Maximum voltage a diode or rectifier can withstand in the reverse direction without breakdown. Compare this rating with your circuit's peak reverse voltage to ensure reliable operation. Always verify against the datasheet's absolute maximum ratings.

Specifies the maximum clock frequency or data rate of the component. This is critical for timing and performance. Verify the speed grade in the datasheet to ensure it meets your system's throughput requirements and that signal integrity is maintained at that speed.

Specifies the maximum continuous forward current the component can handle without damage. Compare this rating with your circuit's operating current to ensure reliable performance. Always verify against the datasheet for derating curves and temperature conditions.

Average value of the rectified current that the device can handle continuously. Compare this rating with your circuit's average load current to ensure reliable operation. Verify against the datasheet's thermal and derating curves for safe design.

Describes the typical use cases or intended market for the component, such as power supplies, automotive, or consumer electronics. Helps engineers quickly assess suitability for their design. Always confirm with the datasheet for detailed specifications and environmental limits.

Specifies the allowable junction temperature range for a semiconductor device. Exceeding this range can degrade performance or cause failure. Engineers should verify this parameter against the datasheet for thermal management and reliability assessment in their application.

Highest current the device can handle for a brief surge, such as inrush or lightning. Essential for power supply and protection circuits. Always compare with your system's surge profile and check the datasheet for duration and repetition rate.

This is the maximum voltage drop across the diode or LED when conducting the specified forward current. It affects power dissipation and efficiency. Compare this value with your circuit's supply voltage and current to ensure proper operation. Always verify against the datasheet for your specific part.

Maximum allowable surge current for a short duration, typically specified for diodes and thyristors. This value indicates the device's ability to withstand transient overcurrents without damage. Verify against datasheet for reliability in surge-prone applications.

Time for a diode to transition from conducting to blocking state. Critical for switching losses in power circuits. Compare values when designing high-frequency converters or rectifiers. Verify against datasheet under specified test conditions.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Describes the internal arrangement of components, such as resistor networks or switch contacts. This affects the circuit topology and pinout. Engineers must verify this configuration against the datasheet to ensure correct integration into the PCB layout and proper functionality.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Harmonized Tariff Schedule code used for customs classification of electronic components. Helps determine duties and regulatory requirements. Buyers should confirm the code with a customs broker for accurate shipping.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Lists any extra characteristics or capabilities beyond the standard specifications, such as built-in protection, special mounting options, or enhanced performance. Review these features to ensure they meet your application's specific needs and compare them across similar parts.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Indicates whether the component is lead-free per RoHS or other directives. Buyers use this to verify environmental compliance and avoid restricted substances. Always confirm with the datasheet or certificate of compliance.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Indicates how the component's case or package is electrically connected, such as to ground, a supply rail, or left floating. This affects thermal management, shielding, and circuit isolation. Always confirm with the datasheet to ensure proper PCB layout and avoid unintended shorts or noise coupling.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Junction capacitance measured at a specified reverse voltage and frequency. This value affects switching speed and high-frequency performance. Compare it with your circuit's requirements and verify against the datasheet for accurate operation.

Recovery time is the interval a semiconductor device needs to return to its blocking state after conducting. It affects switching losses and high-frequency performance. Compare this parameter across diodes and transistors to ensure your circuit meets timing requirements. Always verify against the datasheet for your operating conditions.

Specifies the highest continuous current the device can deliver or absorb at its output without exceeding thermal or electrical limits. Compare this value with your load requirements and verify it against the datasheet's operating conditions, including temperature derating and supply voltage.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

JEDEC standard code that defines the package outline and dimensions. Use it to verify physical compatibility and footprint before PCB design. Compare with the datasheet to ensure the component meets your assembly and manufacturing requirements.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.