LTM4637IV#PBF DC DC Converters от Analog Devices Inc

Specifies the plating material on component terminals, affecting solderability, corrosion resistance, and long-term reliability. Compare finishes like tin, gold, or silver for your assembly process and environmental requirements. Verify against datasheet for compliance.

Defines the control method used by a power management IC, such as voltage mode, current mode, or hysteretic. This affects transient response, stability, and external component selection. Ensure the mode matches your application's performance needs.

Specifies the switching regulator control method, such as PWM, PFM, or burst mode. This affects efficiency, noise, and transient response. Engineers should verify the technique against the datasheet to ensure it matches the application's power requirements and EMI constraints.

Specifies the highest input voltage the component can safely handle without damage or malfunction. Compare this value with your power supply output and any transient spikes. Always verify against the datasheet's absolute maximum ratings to ensure reliable operation.

Specifies the typical input voltage level for which the component is designed to operate. Compare this value with your power supply output to ensure compatibility. Always verify against the datasheet for absolute maximum ratings and operating conditions.

Indicates the topology of the internal switching regulator, such as buck, boost, or buck-boost. This determines the input-output voltage relationship and efficiency. Verify the configuration against your power supply requirements and the datasheet to ensure correct operation.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Shows whether the component complies with the EU REACH regulation. Essential for legal market access in Europe. Check the manufacturer's latest statement to confirm that no substances of very high concern are present above the threshold.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Specifies the ambient temperature range within which the component reliably functions. Compare this with your application's thermal environment to ensure proper operation. Always verify against the datasheet for derating curves and maximum ratings.

Shows if the component meets a specific industry standard or reliability level. Buyers should verify this against the datasheet to ensure the part is suitable for their application's environmental and performance requirements.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Describes the physical configuration of the component's leads or pads, such as through-hole, surface mount, or gull-wing. This affects PCB layout, soldering process, and mechanical fit. Confirm compatibility with your assembly method and footprint.

Current stage in the product's lifecycle, such as Active, Obsolete, or End of Life. This indicates availability and long-term supply risk. Check this before designing in a part to ensure it will be available for your product's production lifetime.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Specifies the electrical form of the output signal, such as digital, analog, or open collector. This determines how the component interfaces with your circuit. Verify the output type against your system requirements and the datasheet to ensure proper signal compatibility and avoid logic level mismatches.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Specify the typical end-use scenarios for this electronic component, such as consumer electronics, automotive, industrial, or telecommunications. This helps engineers quickly assess suitability for their design. Verify against the datasheet's application section.

Select the component category that best matches your application, such as resistor, capacitor, diode, or connector. This classification helps narrow down the correct part family and ensures compatibility with your circuit design. Verify the type against the datasheet to avoid mismatches.

Specifies the count of independent functions or channels integrated into a single component package. This helps engineers determine if the part can handle multiple signal paths or operations simultaneously. Verify against the datasheet to ensure the device meets your circuit's functional requirements.

Mounting type: surface mount or through-hole. Surface mount components are placed directly on the PCB, saving space and enabling automated assembly. Through-hole components offer stronger mechanical bonds. Verify the mounting style matches your PCB design and assembly process.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Specifies how many independent output channels the component provides. Compare this when selecting power supplies, drivers, or modules to ensure the device can drive all required loads. Always verify against the datasheet for exact output configuration.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Specifies the highest voltage the device can deliver at its output under specified conditions. Compare this limit with your application's supply and load requirements to ensure safe operation and avoid overvoltage damage.

Specifies the lowest input voltage at which the component operates correctly. Compare this value with your power supply's minimum output to ensure reliable startup and performance. Always verify against the datasheet's operating conditions.

Efficiency indicates how effectively a power component converts input power into useful output power, expressed as a percentage. Higher efficiency means less energy lost as heat, which is critical for thermal management and system reliability. Always verify the efficiency curve in the datasheet under your operating conditions.

The amount of current the device draws from its power supply during normal operation. This is essential for power budget calculations, thermal management, and selecting appropriate power sources. Check datasheet for typical and maximum values under specified conditions.

Specifies the regulated voltage level available at the output pin under specified load and input conditions. Compare this value with your circuit requirements and verify against the datasheet's tolerance and temperature derating.

Specifies the lowest output voltage the component can reliably provide under specified conditions. Compare this value with your circuit's minimum required voltage to ensure proper operation. Always verify against the datasheet's electrical characteristics and test conditions.

Current supplied at the output, indicating the load-driving capability of the component. This is crucial for ensuring the component can drive downstream circuitry without overheating or voltage drop. Compare with your load requirements and check the datasheet for maximum ratings.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Specifies the highest continuous current the device can supply at its output without exceeding thermal or electrical limits. Compare this value with your load requirements and derating curves. Always verify against the datasheet for your operating conditions.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

This attribute highlights special characteristics or functions of the component, such as built-in protection, mounting style, or unique performance traits. Engineers compare these features to match specific application requirements. Always verify against the datasheet for complete specifications.

Physical dimensions of the component, typically length, width, and height. These measurements are critical for PCB layout and mechanical fit. Always verify against the datasheet for exact tolerances and mounting requirements.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Total number of pins or terminals on the component package. Essential for footprint design, PCB layout, and connector mating. Verify against the datasheet to ensure compatibility with your board and assembly process.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Specifies the nominal or regulated output voltage provided on the first output channel of a multi-channel power supply or DC-DC converter. Verify this value against the datasheet to ensure it meets your circuit's requirements, especially for precision or load-sensitive applications.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Indicates the rate at which the power device toggles between on and off states. Higher frequencies allow smaller magnetics but increase switching losses. Verify this parameter against your application's requirements and the datasheet's recommended operating conditions.

Identifies the core product family without package, grade, or option suffixes. Use this to compare equivalent components across manufacturers and to locate the primary datasheet. Verify the full ordering code against the manufacturer's specification before design-in.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates whether the product contains substances of very high concern as per the REACH regulation. Buyers should verify this for compliance with EU environmental standards, especially when exporting to Europe. Check the manufacturer's declaration or datasheet for accurate SVHC status.

This code indicates the terminal finish material per JESD-609 standard. It helps identify the plating type for soldering compatibility and environmental compliance. Check the datasheet for the exact code and its meaning.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.