GSD2004WS-G3-08 Diodes - Rectifiers - Single от Vishay

Specifies the maximum clock frequency or data rate of the component. This is critical for timing and performance. Verify the speed grade in the datasheet to ensure it meets your system's throughput requirements and that signal integrity is maintained at that speed.

This is the maximum voltage drop across the diode or LED when conducting the specified forward current. It affects power dissipation and efficiency. Compare this value with your circuit's supply voltage and current to ensure proper operation. Always verify against the datasheet for your specific part.

Small current flowing through a semiconductor junction when reverse voltage is applied. Lower leakage is preferred for precision and low-power circuits. Check this parameter at the specified reverse voltage to ensure it meets your application's requirements.

Select the diode classification such as Schottky, Zener, or standard rectifier. This defines the device's electrical behavior and typical applications. Verify the exact type against the datasheet to ensure it meets your circuit requirements for voltage, current, and switching speed.

Forward voltage is the voltage drop across a diode or LED when it conducts current in the forward direction. It affects power dissipation and efficiency. Compare this value with your circuit's supply voltage and check the datasheet for the specified test current.

Maximum allowable surge current for a short duration, typically specified for diodes and thyristors. This value indicates the device's ability to withstand transient overcurrents without damage. Verify against datasheet for reliability in surge-prone applications.

Time for a diode to transition from conducting to blocking state. Critical for switching losses in power circuits. Compare values when designing high-frequency converters or rectifiers. Verify against datasheet under specified test conditions.

Indicates the highest repetitive reverse voltage the diode can withstand in blocking mode. Engineers compare this to the circuit's peak reverse stress to ensure reliable operation. Always verify against the datasheet for your specific application.

Specifies the allowable junction temperature range for a semiconductor device. Exceeding this range can degrade performance or cause failure. Engineers should verify this parameter against the datasheet for thermal management and reliability assessment in their application.

Average value of the rectified current that the device can handle continuously. Compare this rating with your circuit's average load current to ensure reliable operation. Verify against the datasheet's thermal and derating curves for safe design.

Specifies the maximum continuous forward current the component can handle without damage. Compare this rating with your circuit's operating current to ensure reliable performance. Always verify against the datasheet for derating curves and temperature conditions.

Maximum allowable DC reverse voltage that can be applied across the component without causing breakdown. This rating is critical for diodes and rectifiers to prevent reverse conduction. Always ensure your circuit's reverse voltage stays below this limit.

Specifies the maximum continuous DC voltage that can be applied in the reverse direction without causing breakdown. Critical for rectifier and protection diodes. Verify against datasheet to ensure safe operating margin in your circuit.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Published indicates the date when the product data was released or updated in the catalog. It helps buyers assess the freshness of the information and whether the component is current or possibly obsolete. Check the datasheet for the latest revisions.

Describes the internal arrangement of components, such as resistor networks or switch contacts. This affects the circuit topology and pinout. Engineers must verify this configuration against the datasheet to ensure correct integration into the PCB layout and proper functionality.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the product series or family, grouping components with similar design and specifications. Helps identify compatible parts and compare within a product line. Verify the series against the datasheet to ensure correct application.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

Specifies the maximum average forward current a diode or rectifier can handle continuously. Compare this value with your circuit's average load current to ensure reliable operation. Verify against the datasheet's thermal derating curves for safe operation.

Junction capacitance measured at a specified reverse voltage and frequency. This value affects switching speed and high-frequency performance. Compare it with your circuit's requirements and verify against the datasheet for accurate operation.

Indicates if the component is designed to withstand ionizing radiation in space, nuclear, or high-energy physics applications. Compare radiation-tolerant vs. radiation-hardened parts for mission-critical designs. Verify the total ionizing dose (TID) and single-event effect (SEE) ratings in the datasheet.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Specifies the physical weight of the electronic component, important for logistics, shipping cost, and mechanical design. Verify the exact weight in the datasheet or packaging information, as it may vary with packaging type and quantity.

Indicates the physical package type as designated by the component manufacturer, such as SOIC, QFN, or BGA. This affects PCB footprint, thermal performance, and assembly processes. Confirm compatibility with your board layout and soldering requirements before design finalization.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.