DA6J101K0R Diodes - Rectifiers - Arrays от Panasonic

Specifies the maximum clock frequency or data rate of the component. This is critical for timing and performance. Verify the speed grade in the datasheet to ensure it meets your system's throughput requirements and that signal integrity is maintained at that speed.

Semiconductor material used in the diode, such as silicon, germanium, or gallium arsenide. Affects forward voltage, speed, and temperature behavior. Choose based on your application's voltage, current, and switching requirements. Verify with datasheet specifications.

Select the diode classification such as Schottky, Zener, or standard rectifier. This defines the device's electrical behavior and typical applications. Verify the exact type against the datasheet to ensure it meets your circuit requirements for voltage, current, and switching speed.

Maximum current that flows through the diode when reverse-biased and off. Compare this value to ensure minimal power loss and proper blocking in circuits. Verify against datasheet for temperature and voltage conditions.

Specifies the maximum non-repetitive forward surge current the diode can handle for a short duration, typically during inrush or fault conditions. Compare with your circuit's worst-case surge to prevent damage. Check the datasheet for pulse duration and waveform.

This is the maximum voltage drop across the diode or LED when conducting the specified forward current. It affects power dissipation and efficiency. Compare this value with your circuit's supply voltage and current to ensure proper operation. Always verify against the datasheet for your specific part.

Maximum allowable surge current for a short duration, typically specified for diodes and thyristors. This value indicates the device's ability to withstand transient overcurrents without damage. Verify against datasheet for reliability in surge-prone applications.

Specifies the maximum continuous forward current the component can handle without damage. Compare this rating with your circuit's operating current to ensure reliable performance. Always verify against the datasheet for derating curves and temperature conditions.

Specifies the highest reverse current that flows through the component when the rated reverse voltage is applied. Compare this value across diodes and rectifiers to ensure minimal leakage and stable operation. Verify against the datasheet for your operating temperature and voltage conditions.

Indicates how many independent functional sections are integrated into a single component package. This matters when comparing multi-channel devices or resistor networks. Always verify the exact element count against the datasheet to ensure it matches your circuit design requirements.

Specifies the maximum continuous DC voltage that can be applied in the reverse direction without causing breakdown. Critical for rectifier and protection diodes. Verify against datasheet to ensure safe operating margin in your circuit.

Average value of the rectified current that the device can handle continuously. Compare this rating with your circuit's average load current to ensure reliable operation. Verify against the datasheet's thermal and derating curves for safe design.

Specifies the allowable junction temperature range for a semiconductor device. Exceeding this range can degrade performance or cause failure. Engineers should verify this parameter against the datasheet for thermal management and reliability assessment in their application.

Indicates the highest repetitive reverse voltage the diode can withstand in blocking mode. Engineers compare this to the circuit's peak reverse stress to ensure reliable operation. Always verify against the datasheet for your specific application.

Time for a diode to transition from conducting to blocking state. Critical for switching losses in power circuits. Compare values when designing high-frequency converters or rectifiers. Verify against datasheet under specified test conditions.

Small current flowing through a semiconductor junction when reverse voltage is applied. Lower leakage is preferred for precision and low-power circuits. Check this parameter at the specified reverse voltage to ensure it meets your application's requirements.

Indicates the floor life of a component before it must be baked prior to soldering. Higher levels require stricter handling and shorter exposure times. Verify the MSL rating in the datasheet to ensure proper storage and assembly conditions.

Indicates whether the component complies with the EU RoHS directive restricting hazardous substances. Buyers should verify this status for regulatory compliance and market access. Check the datasheet or certificate for exact compliance details.

Harmonized Tariff Schedule of the United States code for customs classification. Essential for import/export documentation and duty calculation. Verify the correct code with a trade specialist to avoid customs delays.

Export Control Classification Number assigned by the U.S. Commerce Department. It determines export licensing requirements for electronic components. Verify the ECCN against the manufacturer's datasheet or export compliance documentation before shipping internationally.

Export Control Classification Number assigned by the U.S. government. Determines whether the component requires an export license. Essential for international trade compliance. Verify the ECCN with the manufacturer or supplier before shipping to avoid legal issues.

Specifies how the component is attached to the PCB, such as through-hole or surface mount. This affects assembly processes, thermal performance, and mechanical strength. Buyers should verify compatibility with their manufacturing capabilities and design requirements.

Specifies the lowest ambient temperature at which the component is guaranteed to function within its electrical and mechanical specifications. Verify this limit against the datasheet for your application's thermal environment, especially for automotive or industrial designs.

Indicates the form of delivery for the component, such as tape and reel, tube, or tray. This affects handling, storage, and assembly processes. Verify the packaging type matches your production requirements and equipment compatibility.

Indicates the typical duration from order confirmation to shipment from the manufacturer's facility. This helps you plan production schedules and inventory. Verify current lead times with your distributor or supplier, as they may vary based on order quantity, product availability, and market conditions.

Lifecycle status of the part, such as active or obsolete. Indicates availability and long-term support from the manufacturer. Check this before design-in to avoid last-time buys or supply disruptions. Verify with the datasheet or distributor for current status.

Position of the terminals on the package, such as dual-in-line, gull-wing, or J-lead. This affects PCB layout, soldering, and thermal performance. Engineers must ensure the terminal position matches the footprint and assembly capabilities of their manufacturing line.

Identifies the company that designed and produced the component. Buyers often filter by manufacturer to ensure brand reliability, quality standards, and supply chain consistency. Verify the manufacturer against the datasheet and official packaging to avoid counterfeit parts.

Physical width of the component body, typically in millimeters. Essential for PCB footprint design and mechanical fit. Verify against the datasheet to ensure proper clearance and compatibility with your board layout and enclosure.

Lists the product categories or classifications assigned to this component, such as connectors, capacitors, or modules. This helps in filtering and comparing similar parts. Review the categories to ensure the component fits your application and to find alternative parts in the same class.

Indicates the specific product subcategories or classifications within the broader component family. Helps narrow down search results and identify the exact type of component needed for your design. Review the subcategory to ensure compatibility with your application.

A more specific classification within the main product category, such as 'Ceramic Capacitor' under 'Capacitors'. This helps narrow down search results and compare similar components. Use it to filter products with similar characteristics and intended applications.

Specifies the metal coating applied to the contact surfaces of connectors, switches, or relays. This finish affects conductivity, corrosion resistance, and durability. Engineers should verify the plating material and thickness against the datasheet to ensure reliable performance in the intended environment.

Specifies how the component attaches to the PCB or assembly, such as surface mount, through-hole, or chassis mount. This affects soldering process, mechanical stability, and thermal performance. Verify compatibility with your board layout and assembly capabilities.

Indicates the total number of electrical connection points on the component, such as pins or pads. This is critical for PCB footprint design and assembly. Verify it matches the package specification to ensure proper soldering and connectivity.

Total number of pins or contacts on the component. This determines the footprint and mating connector requirements. Always match the pin count to your PCB layout and connector specification to ensure proper electrical and mechanical connection.

Indicates the component's compliance status with the EU REACH regulation. Buyers should verify this code against the manufacturer's declaration to ensure restricted substances are within allowable limits for their target market.

Maximum temperature during reflow soldering that the component can withstand. This is critical for solder joint reliability and preventing damage. Verify that the peak reflow temperature is compatible with your soldering profile and the component's moisture sensitivity level.

Maximum time the component can be exposed to the peak reflow temperature during soldering. Exceeding this duration may cause damage or degrade reliability. Ensure your soldering profile stays within this limit and check the datasheet for exact conditions.

Specifies the physical length of the component body, typically in millimeters. This dimension is critical for PCB layout and mechanical fit. Verify against the datasheet to ensure proper clearance and alignment in your design.

Specifies the highest ambient temperature at which the component reliably functions. Compare this limit with your application's thermal environment to ensure safe operation. Always verify against the datasheet's derating curves and test conditions, as exceeding this value may cause performance degradation or permanent damage.

Physical height of the component, measured from the mounting surface to the topmost point. This dimension is critical for clearance in compact assemblies and for ensuring proper fit within enclosures. Always verify against the datasheet for tolerance and mounting considerations.

Physical package or case type of the component, defining its dimensions, mounting style, and thermal characteristics. Common types include SMD, through-hole, BGA, and QFN. Choose the package that fits your PCB layout and assembly process. Verify the exact package code in the datasheet for footprint compatibility.

Specifies the maximum average forward current a diode or rectifier can handle continuously. Compare this value with your circuit's average load current to ensure reliable operation. Verify against the datasheet's thermal derating curves for safe operation.

Arrangement of diodes within the component, such as single, dual, common cathode, or bridge. This determines the electrical behavior and pinout. Verify the configuration matches your circuit design to ensure correct current flow and avoid unintended connections.

Recovery time is the interval a semiconductor device needs to return to its blocking state after conducting. It affects switching losses and high-frequency performance. Compare this parameter across diodes and transistors to ensure your circuit meets timing requirements. Always verify against the datasheet for your operating conditions.

Specifies the reverse voltage applied to a semiconductor device during testing to verify its blocking capability. Engineers compare this value with the maximum rated reverse voltage to ensure safe operation. Always check the datasheet for test conditions and duration.

Indicates the range of frequencies over which the component is designed to operate with specified performance. Use to match your application's signal frequency. Confirm with datasheet graphs for impedance, gain, or attenuation across the band.

The unique part number assigned by the original component manufacturer. Use this to cross-reference datasheets, verify specifications, and ensure the exact component matches your design requirements. Always confirm the number against the manufacturer's official documentation.

Specifies the maximum junction capacitance of the diode under given conditions. Important for high-frequency switching and RF applications where capacitance affects speed and tuning. Verify with datasheet capacitance versus reverse voltage curves.